A well-mixed, insulated water storage tank isto be maintained at internal temperature60°C. The environmental temperaturearound the tank varies from -25°C to 30°C.The tank's exterior surfaces (total = 125m²) have four different levels of insulationas indicated in the table.SurfaceComponent Area,Effective RSI,22 m². °C/Wm²Surface A60.0Surface B30.0Surface C30.0Surface D5.0Saythat just one surface can be selected tohave its insulation upgraded such that itseffective RSI would be doubled. Whichshould be selected to achieve the greatestreduction in heat loss?10.015.04.00.5

For any material, it's insulation capacity is defined by thermal resistance value which can be…

A well-mixed, insulated water storage tank is to be maintained at internal temperature 60°C. The environmental temperature around the tank varies from -25°C to 30°C. The tank's exterior surfaces (total = 125 m²) have four different levels of insulation as indicated in the table. Surface Effective RSI, Component Area, m².°C/W m² 2 60.0 Surface A Surface B Surface C Surface D 5.0 Say that just one surface can be selected to have its insulation upgraded such that its effective RSI would be doubled. Which should be selected to achieve the greatest reduction in heat loss? 30.0 10.0 30.0 15.0 4.0 0.5

A well-mixed, insulated water storage tank is to be maintained at internal temperature 60°C. The environmental temperature around the tank varies from -25°C to 30°C. The tank's exterior surfaces (total = 125 m²) have four different levels of insulation as indicated in the table. Surface Effective RSI, Component Area, m².°C/W m² 2 60.0 Surface A Surface B Surface C Surface D 5.0 Say that just one surface can be selected to have its insulation upgraded such that its effective RSI would be doubled. Which should be selected to achieve the greatest reduction in heat loss? 30.0 10.0 30.0 15.0 4.0 0.5

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter11: Temperature And Temperature- Related Variables In Engineering

Section: Chapter Questions

Problem 34P

See similar textbooks

Similar questions

Determine the thermal conductivity of brickwork of cavity wall comprising 220mm brickwork, 12mm plaster, 80mm cavity, k values are plaster 0.6W/m°C, cavity resistance 0.18m"C/W, internal resistance 0.12m²"C/W, external resistance 0.06 m"C/W. U value of the wall is 1.78.
1:A. If (PB-PA=97.4 kpa), Find (H). B. Write dynamic viscosity in MLT and FLT systems. Meriam red oil, s.g.-0.827- Water- A T 17cm 34 cm B -Mercury
Find the GSB, GSA and the absorption ratio when the oven dry mass is A = 200, in air B = 2020, and in water C = 1250.
Solve for what is being required. Room dimensions are: LxWxH = 8.50 m, 5.0 m, 3m. Originally, the room had linoleum flooring with an absorption coefficient of 0.03. Two opposite walls were cladded with unglazed bricks with an absorption coefficient of 0.02, the one having the entrance gypsum door (2.1 m X 0.80 m) with 0.05 abs.co.; the other two were just bare concrete with sliding glass window openings of 1.80m x 1.20 m each; the bare concrete with an abs.co. Of 0.31 and the window glass with 0.18, the ceiling, too , had bare concrete as its finish at 500 Hz. The client would like to renovate the space into an acoustical studio room and would like to change the ceiling and the flooring. The ceiling will have a vinyl faced fiberglass panel with an abs.co. of 0.71, and the floor will have mineral fiber tiles with an abs.co. Of 0.66, all at 500 Hz.
lysimeter is used to measure infiltration В evaporation (c) evapotranspiration vapor pressure
Nowwww
Q-Water flows through a pipe having an inner radius of 10 mm at the rate of 36 kg/hr at 25° C. The viscosity of water at 25°C is 0.001 kg/m.s. The Reynolds number of the flow is
Within few minutes
11. Change 15°F to degree kelvin Complete FBD, FORMULA, AND SOLUTION
Calculate the heating value of below gas composition
How thick must the insulation layer be to achieve the requirement U = 0.18 W/m2K?A wall of ventilated facade with insulation must meet requirements:Bearing construction: Lightweight concreteλ lightweight concrete = 0.14 W/mK, d=100 mmλ insulation = 0.04 W/mK, d=? etcCold bridges 15% Guide to task 1:1) The requirement for the U-value with regard to cold bridges will be U - 15%.2)Ri for walls: 0.13 m2K/WRu for walls: 0.04 m2K/W
Climate: Avg. Temperature is 3.2°C July 2.5% high is 22.8°C, J Degree Days is 5000 Inside Air Temp. is 20°C Wall Construction, Inside to Out: ● · . Qigihar House in Heilongjiang Province, China Heat Loss Problems, BSCI 2101 . 1. January 2.5% low is -26.0°C 15mm Gypsum Plaster, Sand Aggregate X Concrete Block, rectangular core, Sand and Gravel 2 core, 200mm 15mm Cement Plaster, Sand Aggregate All 4 walls measure the same, 8m wide by 7m tall. The house is heated with electricity at a cost of $0.10/kWh 4. Calculate the January heating cost for the building. 1. Calculate the RSI-total for the walls using the tabular method demonstrated in class, and the temperature drop through each element for the January 2.5% temperature. 2. Calculate the rate of heat flow through the wall again for the January 2.5% temperature. 3. Plot the temperature profile approximately to scale through a vertical cross-section of the wall. 5. Calculate the annual heating cost for the building. 用国 8m 6. Now add 2"…