Given: A steel rod (A= 150 mm?) is stretched between two fixed points with a tensile load of 5000 N at 20°C. a.) What will be the stress at -20°C? b.) At what temperature will the stress be zero? Assume a = 11.7 µm/m°C, and E = 200 Gpa

Given: A steel rod (A= 150 mm?) is stretched between two fixed points with a tensile load of 5000 N at 20°C. a.) What will be the stress at -20°C? b.) At what temperature will the stress be zero? Assume a = 11.7 µm/m°C, and E = 200 Gpa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A cylindrical rod is fixed between two walls. The rod is composed of two materials. Section AC is made of one material (GAC = 2G) while section CD is made of a different material (GcD = G). A torque, T, is applied at point B, as shown below. Jac = JcD = J = 2 in. GẠC = 2G = 20 x 10ʻ psi T= 300 kip in. GCD = G = 10 × 106 psi A D 2L Determine the reactions at the wall, Ta, and Tp. Specify the direction for each. (Note: this is an example of a no calculator problem.) Ans: TA = 250 kip in ( Tp=50 kip in ( T Fixed Fixed to wall to wall
Please read the instructions carefully and do what are asks. Illustrate and show the COMPLETE SOLUTIONS.
A steel plate 5/16 in. thick is embedded in a horizontal concrete slab and is used to anchor a high-strength vertical cable as shown in the figure below. The diameter of the hole in the plate is 0.75-inches, the ultimate strength of the steel used is 36 ksi, and the ultimate bonding stress between the steel plate and concrete is 300 psi. The designers considered a factor of safety of 3.60 is desired when P = 2.5 kips. Address the following: (a) Identify three potential failure modes for the complete system. For each mode develop a sketch which idealizes the mode of failure. (b) If you where required choose dimensions for the plate ("a" and "b"), how would you size these dimensions? (c) For one of the failure modes identified above, perform an analysis to determine adequate plate dimensions ("a" and "b") to support the required load of 2.5 kips with the established factor of safety. in. AP Sl 4 in.
How would maximum load change if temperature was increased? Maximum change in depth is 0.4mm.
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 270 mm, a cross-sectional area of A = 13520 mm², and a length of L = 4.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1830 με. Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. P Answer: Δd = i d eTextbook and Media Save for Later L mm Attempts: 0 of 5 used Submit Answer
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.86 in.² and bar (2) has a cross-sectional area of 0.47 in.2. After load P is applied, the strain in bar (1) is found to be 780 μe. Assume L₁-52 in., L₂=74 in., a=20 in., b=25 in., and c-33 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. Answers: (a) σ1 (b) VD=i (c) P = i L eTextbook and Media Save for Later (1) B L2 b (2) ksi, 0₂ = in. kips. i D P ksi. Attempts: 0 of 5 used Submit Answer
An axial load P is applied to a 150"-long continuous bar with the cross-sectional areas (4) shown in the figure below. The stress-strain relation of the material used to make this bar obtained during a tension test can be expressed as follows: P € = A = 1 in² -50"- O 16000 where o is the normal stress in ksi. a) Determine the axial elongation (in inches) and strain (in %) of the bar when P = 5 kips. b) Find the permanent elongation (in inches) and strain (in %) of the bar after removal of P in a). + (165)³ A = ¹in² 100"- P Note: You can assume that the elastic modulus (E) of material of the bar is equal, at all times, to the slope of the stress-strain curve at the origin.
2
a) Calculate the principal strains, given that the state of plane strain for an element is: E = 25microns E, = 100microns Yy =-45microns b) An axial load of 3 kN is applied to the solid tubular member as shown in Figure 1. The length of the tube is 2.5 metres, the radius is 15 mm. The modulus of elasticity is 200 GPa. Calculate the elongation due to the loading, giving the answer in microns. Length of tube: 2.5m 8 Load: 3 kN Radius of tube: 15mm Figure 1
As shown in the figure, three wires with different areas and modulus of elasticity are used to lift a load W. Their unstressed lengths are L1, L2, and L3. (a) What stress exists in the longest wire, and (b) shortest wire? (c) Determine the stress in the shortest wire if W = 500 Ib. (d) What should be the load so that the two wires will stretch to the length of the longest wire?
Question 2 Consider the bar in figure 2, it has cross sectional area A 1.10-4m², modulus of elasticity E = = 200GPa, and length 1.5 m. The bar is fixed to a wall on its left hand side, and has a constant loading of 1(x) = −10 kN/m applied along its length. x=0.0 |(x) = -10 kN/m 1.5 m X x=1.5 Figure 2: diagram of bar subject to applied force along its length a) The displacement of the bar u(x) is governed by the equation ə du(x) AE dx dx +1(x) 0 x = [0, 1.5], state the two boundary conditions for this bar problem, and give a short reasoning for your answer (maximum 2 sentences for each boundary condition).
Problem. A load of 98 kg is supported by a wire of length 1.8 m and cross-sectional area 0.12 cm². The wire is stretched by 0.2 cm. Find the stress, strain, and Young's modulus for the wire. Answer: 8x10' N/m2; 0.11x102; 7.2x101º N/m?.