:For the two frame member shown F = 40 kN- Diameter of bolt = 10 mm- %3D Determine the horizontal and vertical - components of reaction at B If the allowable bearing stress for the - frame material is 50 MPa what is the required thickness for member BC

Q: 5. A steel tube and an Plates and an axiad Compressive force P pelied. Find the magnitudes ot forcas…

A: Axial compressive force P=-21 kN orP=-21×103 NAsteel=2AAlEsteel=3EAl

Q: Problems. 1 Determine the required 1.5m cross-sectional area of t the bar BC if allowable 1.5m…

A:

Q: determine the force in each member of the Pratt Truss and state if the members are in compression or…

A:

Q: The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each…

A:

Q: Observe the figure that shows the assembly of the ACD arm, suspended by a bearing in C coupled to a…

A:

Q: Problem 6. The A-36 steel pipe has an outer radius of 20 mm and an inner radius of 15 mm. If it fits…

A: Given: The outer radius of pipe ro=20 mm=0.02 m The inner radius of pipe ri=15 mm=0.015 m Distance…

Q: Solve the reinforcement using the method of nodes. Calculate the reactions and forces in the bars…

A: Consider the following FBD Reactions can be calculated by equilibrium equations Taking sum of…

Q: The internal drag truss for the wing of a light airplane is subjected to the forces shown. Determine…

A:

Q: In the assembly shown, rod AB is made of steel (E = 200 GPa) and has a diameter D = 50 mm. Rod BC is…

A: Given data: STEEL…

Q: Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of…

A: Given data: 'AC' is a rigid member pinned at 'A'. 'BD' is a steel link supporting 'AC' at 'B'.…

Q: Two aluminum rods AB and BC hinged to rigid supports, are pinned together at B to carry a vertical…

A: Given data as per the question P =3000 lb cross-section area =0.5 in2 E=10×106 psi Calculations…

Q: rmine the support reaction at D pade of solid cvlindors: ARİS S

A:

Q: A.) If the F = { - 200i + 400j } N , determine the force in each member and state if its in…

A:

Q: show complete solution with free body diagram The frame in the figure supports the 50-kg cylinder.…

A:

Q: Required information Rod BD is made of steel (E = 29 x 106 psi) and is used to brace the axially…

A: According to the given dataE=29x106psiP=106 kipsFBD=0.014PΔlBD = 0.0009ACWe need to find Diameter…

Q: The rigid beam shown is supported by a pin at A and two steel rods each of diameter 16 mm. If P = 30…

A:

Q: The 7/8-in.-diameter pins at A and C that support the structure are in single shear. Find the…

A:

Q: 3 a M The scheme of supporting of the absolutely rigid body is shown in the picture. The minimal…

A: Given data: The value of a is a = 1.6 m. The magnitude of the moment is M = 8 kN-m. The admissible…

Q: Determine the reaction loads and maximum shear stress ! 200 Ibf-in z-in dia. A B 4 in 6 in

A:

Q: A column is clam- ped at the bottom and is carrying a vertical load F, at the center of F. F the top…

A:

Q: The bell crank shown is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

A:

Q: The smallest allowable length L of the bearing plate is in.

A: Given data

Q: If the gap between C and the rigid wall at D is initially 0.08 mm, determine the support reactions…

A: Given data: Deformation, δ=0.08 mm The value of, P=500 kN Young modulus, E=200 GPa. Calculate the…

Q: The homogeneous bar AB weighing 2000 lb. is supported at either end by a steel cable. Calculate the…

A:

Q: Urgent. P = 18 kN

A:

Q: 4. Given the beam loaded as below, label the stress blocks for points A and B. A A

A: Given

Q: The composite bar is firmly attached to unyielding supports. Compute the stress in each material…

A: Given P = 320 kN = 320 X 103 N To find Stress of each materials

Q: PROBLEM 3. The aluminum rod has a solid circular cross-section and supports the loading shown.…

A:

Q: The steel member shown below has a diameter of 69 mm, modulus of elasticity of E = 200 GPa, and is…

A:

Q: 4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…

A: To find: The stress in the rods. Given: The young modulus of steel is Esteel=205 GPa and Ecopper=100…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: 1. A 620 N force P is applied to a frame consisting of members ABC and BD at point A as shown below.…

A:

Q: The rigid block has a weight of 100 kip and is to be supported of steel (A and C) and brass(B) posts…

A:

Q: Problem # 1: For the trussloaded as shown, calculate the axial stress developed in members CD ND and…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 16 kN. Assume that a = 250 mm,…

A:

Q: Required: Determine the magnitude F,' of the single uniformly distributed load in the x- direction…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.