For the network in Figure 2, show the number of steps which are needed to send a packet from PC1 to PC2? Then show the following information in packet header for every step: (1) Source MAC. (2) Destination MAC. (3) Source IP. (4) Destination IP MAC-0:0:0:2 MAC-0:0:0:3 IP- 192.168.1.2 IP- 192.168.2.2 2901 Router 1 2901 Router 2 MAC=0:0:0:4 MAC=0:0:0:1 IP= 192.168.1.1 IP- 192.168.2.1 PCPT PC-PT PC1 PC2 Figure (2).

For the network in Figure 2, show the number of steps which are needed to send a packet from PC1 to PC2? Then show the following information in packet header for every step: (1) Source MAC. (2) Destination MAC. (3) Source IP. (4) Destination IP MAC-0:0:0:2 MAC-0:0:0:3 IP- 192.168.1.2 IP- 192.168.2.2 2901 Router 1 2901 Router 2 MAC=0:0:0:4 MAC=0:0:0:1 IP= 192.168.1.1 IP- 192.168.2.1 PCPT PC-PT PC1 PC2 Figure (2).

A+ Guide to Hardware (Standalone Book) (MindTap Course List)

9th Edition

ISBN:9781305266452

Author:Jean Andrews

Publisher:Jean Andrews

Chapter8: Connecting To And Setting Up A Network

Section: Chapter Questions

Problem 15RB

See similar textbooks

Similar questions

The TTL behaviour for IP-to-Label or Label-to-IP connections is depicted in the below image. Ingress LSR receives a packet with a TTL value of 289 arriving. What would the TTL value be for the ingress and egress LSRs? the letters (A, B, C, D, E, F, G, and H). TTL = 289 MPLS Label IPv4 Packet Ingress LSR TTL = A: TTL = B: LSR TTL= C: TTL=D: X LSR TTL=E: TTL=F: Label Switched wh TTL= G: LSR TTL=H: Egress LSR
A simple CIDR routing table is shown in Figure 1. For each of the destination IP addresses below, indicate which entry in the table it matches. Indicating none if no routing entry can be matched (hint: given an IP packet, the router will check whether there is a routing entry which can be used to route this packet, by checking the destination IP address in the packet with each routing entry: based on the subnet mask of each routing entry, it can extract the network ID and compare it with each routing entry; if there are a few routing entries which can match, the entry with the longest subnet mask wins). Address Mask Output Port 10.19.0.0/16 1 10.19.128/17 2 10.19.192/18 3 10.19.192/19 4 0.0.0.0/1 5 141.219.2.10 10.10.10.10 10.19.86.141 10.19.193.6 10.19.255.86 10.19.192.18
The TTL behaviour for IP-to-Label or Label-to-IP connections is depicted in the below image. Ingress LSR receives a packet with a TTL value of 289 arriving. What would the TTL value be for the ingress and egress LSRs? the letters (A, B, C, D, E, F, G, and H). TTL=289 MPLS Label IPv4 Packet Ingress LSA TTL= A= TTL= B: LSR TTL=C: TTL=D: LSA TTL=E: TTL=F: Label Switched Ph LSA TTL = G: TTL=H: Egress LSR
IP datagrams on a specific network can carry a maximum of only 440 bytes in the data portion. A node on this network, running an application using TCP generates a TCP segment with 1,900 bytes in the data portion. How many IP packets are transmitted to carry this TCP segment, and what are their sizes (including the header of 20 bytes)?
Q3: If a routing table of a router is depicted by the following table, what is the next hop for a packet to be delivered to the IP address 195.82.207.101? (circle your answer in the table) Network Next Hop 195.82.207.0/24 195.82.207.104/30 195.82.207.100/30 195.82.207.96/29 R1 R2 R3 R4
Host A sends the information of size 3000 bytes to Host B using TCP protocol. As long as Host B receives each packet in size 1000 bytes, Host B must acknowledge Host A. We assume the header size in each packet is 40 bytes. How many packets does Host A send to Host B totally? Question 18 options: 3 4 2 5
The first of these packets is from your computer to the DHCP server telling it to release the lease on your IP address. The next 4 packets renew that lease. Note that the source address on the “DHCP Discover” and “DHCP Request” packets is 0.0.0.0. This indicates that your computer does not actually use its new IP address until the interchange has completed. Also note that the destination address in each of the 4 packets is a broadcast address[1]. It should be obvious to you why the first two packets are broadcasted, but what about the last two? Can you explain this? Answer the questions in your Word document right after you post a snapshot of the DHCP packet screen. (#4)
Q: Describe in detail how TCP packets flow in the case of TCP handoff, along with the information on source and destination addresses in the various head- ers.
For the three-way handshake shown in Figure 15 above write out the specifications for the three synchronization packets: SYN1, SYN2, SYN3, if i) the sequence numbers for the client (x) and server (y) start at 40 and 50 respectively, and ii) the packet lengths for pl1, pl2 and pl3 are 60, 70 and 80 respectively.
In the figure below a router is transferring packets, each of length L= 5 000 bits over a link with a transmission Rate R= 1 Mbps to another router at the other end of the link. The speed prorogation of the light signal on the link is 3x108 m/s. The length of the link is 1 Km. L: packet length (in bits) R: link transmission rates (Mbps) Queue of packets waiting for output link 1-Calculate the total transmission delay. 2- How many packets can be transmitted in one second.
A TCP message consisting of 2100 bytes is passed to IP for delivery across two networks. The first network can carry a maximum payload of 1200 bytes per frame and the second network can carry a maximum payload of 400 bytes per frame, excluding network overload. Assume that IP overhead per packet is 26 bytes. What is the total IP overhead (in bytes) in the network for this transmission?
Assume that a Host A contacts a name server B to get a cached DNS response (i.e., B does not have to go to the root name server, TLD name server, or authoritative name server to get a response). Suppose that A and B can communicate using UDP or TCP. However, any packet sent from A to B or from B to A has an independent chance of being lost of 10%. Let the round trip time for a packet to go from A to B and back (or B to A and back) be RTT. Let A start at a time = 0s. When the time is 2RTT, which of TCP or UDP is the better option for A to get the DNS response from B? Better here means higher probability of correctly receiving the DNS response