Refer to the figure below. The IP and MAC addresses are shown for nodes Petra and Bhoy, as well as for the router's interfaces. Consider an IP datagram being sent from node Petra to node Bhoy. Assume Petra knows the IP address of Bhoy and the IP and MAC addresss of the router. Give the source and destination Ethernet addresses, as well as the source and destination addresses of the IP datagram encapsulated within the Ethernet frame at points (1), (3), and (5) in the figure. PETRA (1) network interface 10.0.3.234 BE-BE-FA-CE-CA-BA (2) 10.0.3.143 BA-DB-01-AD-DO-BO router 10.0.32.64 (3) FE-ED-DE-AD-BE-EF IP source, destination address: (3) Ethernet source, destination address: IP source, destination address: (5) Ethernet source, destination address: IP source, destination address: layer-2 switch Kindly write your answer in this format on your answer sheet: (1) Ethernet source, destination address: Co-FF-EE-4D-BE-BE 10.0.32.245 (4) end host BHOY (5) INDAY

Refer to the figure below. The IP and MAC addresses are shown for nodes Petra and Bhoy, as well as for the router's interfaces. Consider an IP datagram being sent from node Petra to node Bhoy. Assume Petra knows the IP address of Bhoy and the IP and MAC addresss of the router. Give the source and destination Ethernet addresses, as well as the source and destination addresses of the IP datagram encapsulated within the Ethernet frame at points (1), (3), and (5) in the figure. PETRA (1) network interface 10.0.3.234 BE-BE-FA-CE-CA-BA (2) 10.0.3.143 BA-DB-01-AD-DO-BO router 10.0.32.64 (3) FE-ED-DE-AD-BE-EF IP source, destination address: (3) Ethernet source, destination address: IP source, destination address: (5) Ethernet source, destination address: IP source, destination address: layer-2 switch Kindly write your answer in this format on your answer sheet: (1) Ethernet source, destination address: Co-FF-EE-4D-BE-BE 10.0.32.245 (4) end host BHOY (5) INDAY

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Suppose that there are three inter-media nodes between Host 1 and Host 2, and the transmission rate of each link is 4.096 Mbps. The time of end-to-end circuit established is 0.5 second. How much seconds does it take to send a file of 8.192M byte from host H1 to host H2 over a packet-switched network?
These diagrams are used for Assignment 5.2. Answers are entered on Moodle. Note on both diagrams: • The gateway router is configured and programmed correctly. • Some of the Computer's IP properties are misconfigured. Diagram #1 Name: IP Address Subnet Mask: Computer A Computer B Computer C 100.200.142.10 100.200.142.11 100.200.142.12 255.255.255.0 255.255.255.0 255.0.0.0 Gateway: 100.200.142.1 100.200.142.2 100.200.142.1 Switch Gateway Router Switch 100.200.142.1 255.255.255.0 Diagram #2 Name: Computer E Computer F Computer G IP Address 180.190.57.10 180.190.57.11 180.190.57.12 Subnet Mask: 255.255.255.0 255.255.255.0 255.255.0.0 Gateway: 180.190.57.1 180.190.57.2 180.190.57.1 Gateway Router 180.190.57.1 255.255.255.0 Computer X Computer Y 100.20.35.101 100.20.35.102 255.255.255.0 255.255.255.0 100.20.35.1 100.20.35.1 100.20.35.1 255.255.255.0 Computer P Computer Q 200.190.35.101 200.190.37.102 255.255.255.0 255.255.0.0 200.190.35.2 200.190.35.1 Switch 200.190.35.1 255.255.0.0 Switch
Consider a TCP connection with the following parameters: a) Initial ssthreshold = 4 segmentsb) Round Trip Time (RTT) = 10 millisecondsc) Timeout period = 40 millisecondsd) Segment size = 3900 bytesThe TCP connection was used to transfer 17 data segments. While sendingthe segments, data segment 7 and data segment 15 were lost the first timethey were sent (but arrived at the receiver properly when retransmitted).There were no other segment losses apart from the aforementioned. Assumethat data segments received out-of-order are buffered at the receiver. Whatis the average throughput obtained in sending all the data segments (inbytes/sec)? Draw a diagram to show the communication process in detail.
The Transport Control Protocol (TCP) is a protocol that operates at the transport layer and provides full duplex, connection-oriented, and reliable delivery services. When we talk about full duplex, reliable delivery, and a focus on connections, what do we mean? Definitions of "connection-oriented," "reliable delivery," and "full duplex"
Consider incoming TCP and UDP segments arriving at a server, and suppose that we see that 100 different destination port numbers are being used. The server acts only as a server (that is, in the socket sense, it does not initiate communication with any other computers as a client; it only responds to incoming segments). Describe the number of sockets being used at this server and justify your answer
Host A is sending an enormous file to Host B over a TCP connection. Over this connection there is never any packet loss and the timers never expire. Denote the transmission rate of the link connecting Host A to the Internet by R bps. Suppose that the process in Host A is capable of sending data into its TCP socket at a rate S bps, where S=10•R. Further suppose that the TCP receive buffer is large enough to hold the entire file, and the send buffer can hold only one percent of the file. What would prevent the process in Host A from continuously passing data to its TCP socket at rate S bps? TCP flow control? TCP congestion control? Or something else? Elaborate.
A common protocol stack used by many applications is to use TCP at the transport layer and IP at the network layer. The ICMP protocol is also used to report on problems encountered by IP. a. The IP protocol provides a service referred to as "best effort". Describe the services of the IP protocol, and potentially ICMP protocol, with respect to flow control (ensuring the sender does not overwhelm the receiver). b. Describe the service TCP provides with respect to flow control and explain the mechanisms it uses to overcome the deficiencies of IP.
- Suppose a TCP message that contains 1024 bytes of data and 20 bytes of TCP header is passed to IP for delivery across two networks interconnected by a router (i.e., it travels from the source host to a router to the destination host). The first network has an MTU of 1024 bytes; the second has an MTU of 576 bytes. Each network's MTU gives the size of the largest IP datagram that can be carried in a link-layer frame. Give the sizes and offsets of the sequence of fragments delivered to the network layer at the destination host. Assume all IP headers are 20 bytes.
Suppose a system has 50 MB data to send on a network and transmit the data in burst at 8 Mbps, the maximum transmission rate across routers in the network is 6 Mbps, if system uses leaky bucket algorithm, the capacity (in MB) that bucket must hold so that no data is discarded is?.
b) TCP demultiplexing. Suppose a process in host C has a TCP socket with port number 787. Suppose host A and host B each send a TCP segment to host C with destination port number 787. Will both of these segments be directed to the same socket at host C? If not, how will the process at host C know that these segments originated from two different hosts?
Assume the VC number of a virtual-circuit network is a 16-bit field. What is the maximum number of virtual circuits that can be carried over a link? If the path and the VC number for each VC are determined by a central node of the network and the same VC number is used for all links along the path of same VC, how does the central node determine the VC number at the setup time?
Consider a TCP segment originating on a host running a Google Chrome Browser destined for the TU Dublin Webserver: (1) Separately identify how the port numbers are assigned for the client and server applications and, identify the range from which these port numbers are allocated. (ii) Identify the byte order used to represent these addresses within the segment header. (iii) If a port number contained in the segment header is passed to the Application layer, identify the function used to convert it to the correct byte order within the application.