For the level process shown in figure,4 m?/minAT = 3 m?8 m4 m³/minR = 1 min/m2A 3-unit amplitude step-type input change is applied that changes to 6 units after 6 minutes andremains constant.1) What is the level height that the system will reach after stabilization?2) What is the level height 15 minutes after the input variation was applied?3) In how long will the system reach 65% of the final value?

Answered: For the level process shown in figure,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Forcing Function Spring Constant (2)4 Mass k Friction Constant b m Mass Displacement y(t) 3. (20 pts.) Consider the following spring-mass-damper mechanical system (it is placed sideways, so that you won't need to consider gravity). The input is given by f(t), and the output is y(t). Find an equation in frequency domain (s domain) that defines the relationship between the input F(s) and the output Y(s).
A test was undertaken to find the dynamic properties of a SDOF system. The measured transient response recorded is shown in Figure QA2a. If the stiffness of the system is 1,000 N/m estimate: i) the damping ratio, ii) the undamped natural frequency, and iii) the mass of the system. Displacement (m) 0.08 0.06 0.04 0.02 O -0.02 -0.04 -0.06 -0.08 Figure QA2a 0.5 Time (s) 1.5 2
Which one is the linearized modelling equation of the given system. 5-3Nm Your answer: O 22 + +72= fa(t) O2+6+11r fa(t) O 2+62 +9r= Ja(1)
A) Assuming that no inputs are present to a first-order and a second-order systems, mention two fundamental differences between the two systems. B) Determine the damping ratio and natural frequency of the single-loop RLC electrical circuit system shown below. d²1 dI I + R + = dt² dt с L E(t). C) State two distinctions between odd and even functions, and name and sketch a function that's neither odd nor even. D) What is the frequency in Hertz and the amplitude of the 5th term (i.e. the 4th harmonics) of the following signal? 4 2π 10π == - sin TT 4 бп y(t) (² t) + 37 sin (17) 4 + sin 5π (10+) +. 10 10
is my entered answer correct ?
Break down how got the answer simply? For period what is as?
Look at the below system. Assume that the forcing function is a sine and cosine response (i.e., F = Focos(wt) and F = Fösin(wt)). If your system has the following variables: m= K= 15 kg 207 F₁ = 168 w = w₁/2 Xo = 1 m/s Vo = -1 m/s Plot both responses of the system.
Two particle of respective masses mi = 4m and m2 = 3m are attached to two spring of respective spring constants k and 3k as shown in the adjacent figure. k ļ 4m 3k 3m a) Write down the Lagrangian of the system. b) Obtain Lagrange equations for each coordinate. c) Calculate the normal frequencies of the coupled oscillations. Deduce which frequency correspond to the symmetric and non-symmetric modes. d) Find the normal modes (eigenvectors) associated with the normal frequencies. e) Deduce a general solution for x1(t) and x2(1). f) Obtain a normal coordinate for each of the normal frequencies.
3. Consider the mechanical system shown in Fig. 3. Let V3(t) be the input and the acceleration of the mass be the output. Derive the state equations and the output equation using linear graphs and normal trees. V,(t) В m k2 101 k, Figure 3: A mechanical system with an across-variable source
ponse Clear selection A block attached to a spring, oscillates on a frictionless horizontal surface with a period of 0.3 s. The time needed by the block to move (for the first time) from position x = A to x = -A/2 is: O 0.2 sec 0.3 sec 0.05 sec 0.1 sec O 0.15 sec
1.block diagram physical meaning and the time response for different inputs
:) Determine the equivalent mass of the system shown in Figure Q.A3c. X m 2r m Figure Q.A3c. m WE For the system shown in Figure QA1a write appropriate response variables and find the degrees of freedom. r= 10 cm /= 1.5 kg-m² m = 10 kg nollos 2k

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS