A system is described by the following equations (both are equivalent), with y as the output and u as the input: аў + bӱ + су %—и ÿ + 23wný + wny = au Parameter Values: a = 0.5, b = 9, c = 18

A system is described by the following equations (both are equivalent), with y as the output and u as the input: аў + bӱ + су %—и ÿ + 23wný + wny = au Parameter Values: a = 0.5, b = 9, c = 18

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i dont really understand the explanation of part b or how they used trigonometry to get that. can you please help.
Question 3) On the plate in the figure, the length L is given as L = 18 m . According to this; y 2L L 2L 3 L -- L Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result as m without writing units.) Response: Question 3-B) Find the Y coordinate of the geometric center of the plate . (Enter your result as m without writing units.) Response:
use even matric number
hi please solve this dof question
The first diagram is wrong, line AB should be longer since its length is equal to 580mm than line P2B which is equal to 360mm, please revise.
Please answer 3, 4, 5, 6, 8, 9, 10, 12 1 is 0, 2 is 0, 7 is point A, 11 is 2. I included a picture of someone who solved but they were mostly incorrect. Please do not answer if the solution set I provided with the incorrect answers was you. I appreciate the attempt, but the solutions for 3, 4, 5, 6, 8, 9, 10, 12 were marked wrong, so unless you have different answers, please do not submit the same incorrect solution set. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the mass center G is set as the origin (datum), the gravitational…
Please do the last three questions (2, 3 and 4)! Thank you in advance! A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center. 1- Two children are sitting on opposite sides of each other on the seesaw. One child weights 50lbs and is sitting 0.7m on the left end. Where should the other child sit in order to be balanced on the seesaw if they weigh 42lbs? 2- Now, a third child wants to sit on the seesaw and weighs 30lbs and is sitting 1.25m in front of them and is closer to the fulcrum on the right side. What are the CW and CCW moment of the seesaw now? What is the net moment and direction? 3- Then, a fourth child wants to play on the seesaw and is on the left side of the plank in order to bring the system to equilibrium. How much does the child weigh (Calculate the pounds of force needed in order for rebalance?) 4- Now the fourth child leaves the other three children sitting on the plank. If the three children are sitting in the same potions as they did…
are you sure it's not c?, can you show with diagrams
Answer according to what is shown in the image. Instructions are already appended in the given image. Thank you
Solidworks
How many 1-cm cubes does it take to construct a cube that is 4 cm on edge?
Please show work for all these answers and a clear and short explantion of each one