Find the maximum shear force (V), the cross section can carry if the maximum shear stress is not to exceed 100MPA. And then after calculating the value of V, FIND the force carried by the web. 200 mm 20mm 20mm V 210mm 20mm 110mm

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

A: The maximum value of Pmax that can be supported by the structure is  128kN

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

A: Given the applied load at A and D are 400 lb and 800 lb respectively  Required: Internal reactions…

Q: The pipe shown in Fig a has an inner radius of 40 mm and an outer radius of 50 mm. If its end is…

A: Given Inner radius of pipe = 40 mm Outer radius of pipe = 50 mm To find The shear stress inner and…

Q: A cantilever beam with the length of 1.2-m is subjected to a load of P = 400-N. Find: a-The stresses…

A: Given:Length of beam = 1.2mP = 400 NFigure is providedTo find:Stress at K & HTotal tensile or…

Q: The cantilever beam is subjected to the point loads P₁ = 2.3 kN and P₂ = 5.9 kN. Part A Determine…

A: According to the given data A loading beam With Loads P1=2..3kN P2=5.9 kN We need to find  Shear…

Q: The elastic portion of the stress–strain diagram for an aluminum alloy is shown in the figure. The…

A:

Q: The handle of the press is subjected to a force of 20 lb. Due to internal gearing, this causes the…

A: Write the expression of the area and axial stress due to axial load acting on the system.

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: To read quetsion carefully

Q: Determine the smallest coefficient of static friction at both A and B needed to hold the uniform…

A:

Q: 4) The bar shown has a cross-sectional are of A and a modulus of elasticity of E. If the axial force…

A:

Q: A timber company has designed a series of beams by bonding the top and bottom flanges to the edges…

A: L1=6 inL2=3.1 inL3=8.75 inL4=1.05 in The vertical shear force is V=3800 lbf

Q: 4. The shear stress-strain diagram for screws used in plating is the standard technique for treating…

A:

Q: The 200-mm square aluminum block supports a compressive load of 300 kN. 300 kN - 30°

A: ANs          FBD Σfx = 0            (Na/a   - 300.cos 30°=0                            Na-a =…

Q: 30 -1.5m A D 80KN 5m 80KN 1.5m 40μN

A:

Q: A timber company has designed a series of box beams with the geometry shown below. The beams are…

A: Given data  Shear force = 8kN  Find the maximum shear stress and shear stress at joint

Q: Determine the magnitude of maximum stress

A:

Q: The circular punch B exerts a force of P = 1.7 kN on the top of the plate A. (Figure 1) Figure <) 1…

A:

Q: The simply supported joist is used in the construction of a floor for a building. In order to keep…

A: Understand due to symmetry of the beam the reactions offered by the supports will be equal and…

Q: 2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the…

A:

Q: Problem: The steel pipe has an inner diameter of 2.75 in and an outer diameter of 3 in. The pipe is…

A: To find: (a) The normal and shear stress at point A and B. (b) The principle stress at point A and…

Q: Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring…

A:

Q: A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown…

A: σa = -83.93MPaσf = -1.35MPaδcolumn = 2.07mmExplanation:

Q: If M = 1 kip # ft, determine the resultant force the bending stresses produce on the top board A of…

A: The depth of centroid is y¯=d2y¯=1.5+12+1.52y¯=7.5 in Expression to calculate the moment of inertia…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.