200 mm 80 N 300 mm 80 N 200 mm 80 N 300 mm (b) Stress free top D TE = 0.276 MPa Tp = 0.345 MPa Stress free inside (c)

Q: The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate…

A:

Q: The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the…

A: Given data: -  The torque at point A is TA = 2T. The torque at point B is TB = 3T. The allowable…

Q: The shaft consists of three concentric tubes, each made from the same material and having the inner…

A: Given data: The magnitude of the torque acting on the shaft, T = 800 N·m. Calculate the polar…

Q: Two solid steel shafts of different diameters are joined together at point C. The diameter of the…

A:

Q: The cylinder of a hydraulic ram supported at the open end is 200 mm internal diameter and is…

A:

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is…

A:

Q: Q1/ The copper pipe has an outer diameter of 3.0 in. and an inner diameter of 2.8 in. If it is…

A:

Q: 1. The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A…

A: To find: The longitudinal and hoop stress developed in the wall of the pipe, also draw the stress on…

Q: d2 mm 60 mm FAN dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the…

A:

Q: Determine the required diameter of the pins at A and B to the nearest 116 in. if the allowable shear…

A: Given, Pin A is subjected to double shear and Pin B is subjected to single shear.

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

A:

Q: The two members are connected by two 20-mm bolts. If P = 10 kN, determine the normal and shear…

A:

Q: 1. The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It…

A: Given data :- The inner radius = 1.25 m                         The thickness of wall = 15 mm…

Q: ss distribution stance. If it yiel s of the yield.

A:

Q: The copper pipe has an outer diameter of 40 mm and an inner diameter of 34 mm. It is tightly secured…

A:

Q: The shaft has a diameter d and is subjected to the loadings shown. Determine the principal stresses…

A: Given: The load acting at the centre of the shaft is P.  The the axial force acting on the shaft is…

Q: The drive shaft of a car is designed to be a tube with an outer diameter of 4 in. The engine…

A: Given the following data:Outer diameter of the shaft, do= 4inPower delivered by the engine, P= 190hp…

Q: Determine the average shear stress in the tube if the dimension a = 200 mm

A:

Q: The A-36 steel pipe in (Figure 1) has a 6061-T6 aluminum core. It is subjected to a tensile force of…

A:

Q: The 2-m-long tube is made of an elastic perfectly plastic material as shown. Determine the applied…

A:

Q: Q-1 Two wrenches are used to tighten the pipe. If P = 350 N is applied to each wrench, determine the…

A:

Q: The adjustable pliers are used to clamp the smooth tube C. If the force of 100 N is applied to the…

A:

Q: The following shaft consists of a tube AB and a solid rod BC. The tube has an inner diameter of 25…

A: Please check sign convention I took compressive as negative.If you have any doubts please comment

Q: The clamp presses the smooth surface at E when tightening the screw. If the tension in the bolt is…

A: Given data as per question Tension in the bolt =40 kN   Support reaction are shwn on FBD (a)Internal…

Q: Determine the maximum shearing stress and elongation in a bronze helical spring composed of 20 turns…

A:

Q: 2. If P = 8 kN, determine the average shear stress in the pins at A, B and C. All pins are in double…

A:

Q: Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a…

A: Here, Shaft diameter = dsh = 50 mm Allowable shear stress in shaft = τsh = 100 N/mm2 Pitch circle…

Q: 4-The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A:

Q: nd hemispherical shells, The bol and the 25 mm diameter bo able normal stress of 150 M

A: given data  tank thickness = 50 mm no of bolt/ length = 40  dia of bolt =25 mm allowable stress for…

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a…

A: F1= 11 kN= 11000 N a= 250 mm b= 100 mm c= 90 mm θ= 40∘ Diameter, d= 29 mm Thickness, t= 31 mm   To…

Q: T P y=-38 MPa Try = 33 MPa q=52 MPa x

A: Consider following plane stress element:here,Find:The principal stresses andThe maximum in-plane…

Q: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is…

A: Given: The thickness of the wall is t=0.025 in. The inner diameter of the wall is d=0.5 in. The…

Q: 8 in 5in 12 in S

A:

Q: The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the…

A: Given Data: Diameter of the shaft, d=24 mm The magnitude of load, P=1 kN

Q: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an allowable…

A:

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem…

A: Consider the diagram shown in the figure. Here, σx=0, σy=-15ksi, τxy=-6ksi, θ=150°. We need to find…

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.