roblemThe two members are connected by two 20-mm bolts. If P = 10 kN, determine the normal andshear stresses in the bolts and the maximum bearing stress on the member. The nuts have anouter diameter of 30 mm.PPGuides to solve the problem:12 mmFront view:30°1. Draw the FBD of one member.2. Solve for the bearing force.3. Section one bolt and solve internal forces.4. Solve for the normal and shear stress in the bolts.5. Solve for the bearing stress in the members due to the nuts.6. Solve for the bearing stress in the members due to the bolts.36 mm36 mmPP

Answered: Image /qna-images/answer/6189254e-7994-4c8b-afa1-22959a27b303.jpg

The two members are connected by two 20-mm bolts. If P = 10 kN, determine the normal and shear stresses in the bolts and the maximum bearing stress on the member. The nuts have an outer diameter of 30 mm.

The two members are connected by two 20-mm bolts. If P = 10 kN, determine the normal and shear stresses in the bolts and the maximum bearing stress on the member. The nuts have an outer diameter of 30 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: For the connection shown, the average shear stress in the 14-mm-diameter bolts must be limited to…

A: Given is a double shear connection.

Q: If the force P equals 2500 lbs. Determine the maximum tensile stress in the section of the hook…

Q: The small steel plate is connected to the right angle bracket by a 6 mm diameter bolt and the…

Q: The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is…

A: Diameter of pin, d=11 mm=0.011 mBar width, w=60 mm =0.060 mBar thickness, t=10 mm=0.010 mThe average…

Q: The bar has a 100 mm by 15 mm rectangular cross section. The allowable normal and shear stresses on…

Q: The rectangular bar is connected to the support bracket with a 26-mm-diameter pin. The bar width is…

A: Given data:- Diameter of pin =26mm. The bar width (w)= 60 mm the bar thickness (t) = 15 mm. Each…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN F2 = 6KN F3 =…

A: Given: F1 = 7KN F2 = 6KN F3 = 2KN F4 = 9KN

Q: The two rods support the vertical force of P = 40 kN. Determine the normal stress in rod AB and AC…

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: The rectangular bar is connected to the support bracket with a 27-mm-diameter pin. The bar width is…

Q: Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each…

A: Force, P = 3 kN = 3000 N Radius, r = 45 mm = 0.045 m Wall Thickness, t = 2 mm = 0.002 m

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

Q: d2 mm 60 mm FAN dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the…

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

Q: The rectangular bar is connected to the support bracket with a 10-mm-diameter pin. The bar width is…

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

Q: The rectangular bar carries a load of P = 102 KN and is connected to the support bracket with a…

Q: 3-Determine the maximum vertical force P that can be applied to the bell crank so that the average…

Q: The d = 16-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN F2 = 6KN F3 =…

Q: The wide-flange beam is subjected to the 50-kN force. Determine the principal stresses in the beam…

Q: The wheel on a trolley is held in place on the leg using a 5-mm-radius pin. If the wheel is…

A: The problem is asking for the average shear stress in the pin. Shear stress is a measure of how much…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

roblem
The two members are connected by two 20-mm bolts. If P = 10 kN, determine the normal and
shear stresses in the bolts and the maximum bearing stress on the member. The nuts have an
outer diameter of 30 mm.
P
P
Guides to solve the problem:
12 mm
Front view:
30°
1. Draw the FBD of one member.
2. Solve for the bearing force.
3. Section one bolt and solve internal forces.
4. Solve for the normal and shear stress in the bolts.
5. Solve for the bearing stress in the members due to the nuts.
6. Solve for the bearing stress in the members due to the bolts.
36 mm
36 mm
P
P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Draw FBD and Find internal forces of the bolts.

VIEW

Find Normal and Shear stress in bolts.

VIEW

Maximum bearing stress in member.

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the problems below: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube has an inner diameter of 25 mm and a wall thickness of 5 mm, determine the maximum shear stress in the tube when the cable force of 600 N is applied to the cables. 600 N 75 mm 5 mm 75 mm -25 mm 600 N
40 mm The yoke-and-rod connection is subjected to a tensile force of 5 kN. Determine the average normal stress in each rod and the average shear stress in the pin A 5 k between the members. 30 mm A 25 mm 5 kN
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths.
Determine the maximum normal stress (in MPa) developed in the bar when it is subjected to a tension of P = 12 kN.
Two wood members of uniform cross section are joined using a simple glued scarf splice. Determine the normal and shearing stresses in the glued splice. The column is loaded in tension through the centroid with the load indicated. 2.4 kip 6" 60° 2.4 kip
Determine the maximum ram force P that can be applied to the clamp at D if the allowable normal stress for the material is sallow = 180 MPa.
An axial force of 52 kN is applied to the assembly shown by means of rigid end plates. 5 mm 5 mm 20 mm 20 mm 5 mm 5 mm Steel core E = 200 GPa Brass shell E = 105 GPa 250 mm Determine the normal stress in the brass shell. The normal stress in the brass shell is MPа.
The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is w = 75 mm and the bar thickness is 20 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax=
Determine the shortest distance d to the edge of the plate at which the force P can be applied so that it produces no compressive stresses in the plate at section a–a. The plate has a thickness of 10 mm and P acts along the centerline of this thickness.
1. The pictured link acts as a part of the elevator control for a small airplane. If the attached aluminum tube has an inner diameter of 25 mm and a wall thickness of 5 mm, determine the shear stress in the outer and inner surfaces of the tube when a cable force of 600 N is applied to the cables. Also, sketch the shear-stress distribution over the cross-section.
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb/ft2, determine the state of stress at points Cand D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe. 6 ft 3 ft 上 A B x 12 ft 150 lb/ft²