A bracket is attached to a vertical column by means of six identical bolts as shown in Fig. It is subjected to an eccentric force of P = 30 kN at a distance of 200 mm from the center of the column. What is the magnitude of maximum shear force and which bolt carry it?

A bracket is attached to a vertical column by means of six identical bolts as shown in Fig. It is subjected to an eccentric force of P = 30 kN at a distance of 200 mm from the center of the column. What is the magnitude of maximum shear force and which bolt carry it?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Related questions

Q: The compound bar is supported by a journal bearing at point E, a thrust bearing at point F and a…

Q: The system shown is subjected to three axial forces P₁ = 250 kN, P₂ = 400 KN and P3 = 275 kN. What…

A: To find: The total change in length due to loading. Given: The length of bar AB is lAB=1 m. The…

Q: The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a…

Q: 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables if…

A: Givencables with load as shown below

Q: A bent pipe is attached to a wall with brackets as shown. A force of F = 105 lb is applied to the…

Q: A frame supports both a linear distributed load and a concentrated moment, as shown in the figure…

A: The distributed load is The moment applied at C is The dimension are

Q: A bent pipe is attached to a wall with brackets as shown. A force of F = 170 lb is applied to the…

A: Given data, Force, F = 170 lb a = 8.68 in b = 14.9 in c = 14.2 in d = 46.5 in h = 29.5 in g = 31 in…

Q: A floor hoist supports an engine of weight WE 2.9 kN. As illustrated in the figure below, the floor…

Q: For the frame and loading shown, find (a) the reaction at A (mag and divec) (b) the reaction at C…

A: according to the given data, we need to find reactions at A , B and C

Q: A bent pipe is attached to a wall with brackets as shown. A force of F= 235 lb is applied to the end…

A: Given data:Force, F = 235 lba = 12 inb = 27 inc = 20.3 ind = 75 inh = 42.5 ing = 50 inAssume D is…

Q: A 7.5kg sign is hung off of the end of a 3.7kg metal arm as shown in the figure. (Note that while…

A: Given Data: The mass of the arm is m1=3.7 kg. The mass of the sign is m2 = 7.5 kg. The center of…

Q: Find the force in member HI

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a - 2 ft • b = 4 ft C = 1 ft then,…

Q: The structure shown in Fig 4-4.17 consists of two simple trusses joined by bars Be, CF and DG. Find…

Q: The truss below is subject to the loads as shown. All of the members are attached at plates and can…

A: The normal force in member AE.Given:The applied loads are .The given truss is shown below.

Q: One end of a uniform { = 3.80-m-long rod of weight w is supported by a cable at an angle of e = 37°…

A: TO FIND; The minimum distance x from point A so that rod does not slips.

Q: A claw hammer is used to pull a nail out of a board (see figure). The nail is at an angle of 60° to…

A: Given data, Angle between the nail and the horizontal surface = 60° Force F1 = 300 N Distance…

Q: A stepped bar is fixed at end C. The bar has a cross sectional area of 1000 mm² in AB, and a 2000…

Q: Consider the frame shown in (Figure 1). Suppose that F₁ = 26 kN. Part A Determine the x and y…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

plz help before -ront The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T₁ 410-N forces act in the - direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and components of force on the shaft. Figure lashel but sol is 300 mm A 200 mm 2 150 mm 150 mm ✓ 200 mm 400 mm B. 200 N 200 N 80 N 80 N 1 of 1 ▾ Part B Determine the resultant shear force in the y direction on the cross section at C Express your answer to three significant figures and include appropriate units. (Vc)y=245.714 Submit Part C Submit * Incorrect; Try Again; 3 attempts remaining Check your signs. (Vc),= 175 ▾ Part D Determine the resultant shear force in the direction on the cross section at C. Express your answer to three significant figures and include appropriate unite. T= 10 ▾ Part E Previous Answere (Mc) Submit M ^ Part Fi * Incorrect; Try Again; 5 attempts remaining…
The bell-crank mechanism shown below is supported by a single-shear pin connection at B and a roller support at C. A load P acts at an angle of θ=40° at joint A. The pin at B has a diameter of 0.375 in, and the bell crank has a thickness of 0.188 in. The ultimate shear strenght of the pin material is 28 ksi, and the ultimate bearing strenght of the crank material is 52 ksi. A minimum factor of safety of 3.0 with respect to shear and bearing is required. Assume that a = 9.0 in. and b =5.0 in. What is the maximum load P that may be applied at joint A of the bell crank?
Problem 2. The assembly consists of three titanium (Ti- 6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 6 kip is applied to the ring F, determine the horizontal displacement of point F, and determine the angle of tilt of rigid bar AC. B D 4 ft ACD = 1 in² AAB 6 ft 1.5 in² E 2 ft 1 ft 1 ft AEF = 2 in² 6 kip
The shaft is supported at its ends by two bearings AA and BB and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T1=T1= 585-NN forces act in the -zz direction and the 200-NN and 80-NN forces act in the +yy direction. The journal bearings at AA and BB exert only yy and zz components of force on the shaft. Part A Determine the resultant normal force on the cross section at CC. Express your answer to three significant figures and include appropriate units. NC= values ? NC= units? Determine the resultant shear force in the yy direction on the cross section at CC . Express your answer to three significant figures and include appropriate units. (VC)y Values ? (VC)y units ?
Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an allowable shear stress of Tallow = 85 MPa, check the allowable force for external and internal diameter of pipe and determine the allowable maximum force P that can be applied to each wrench. The pipe has an outer diameter of 25 mm and inner diameter of 20 mm. 250 mm B 250 mm Figure 4 Answer: Torque = 0.5P, Polar moment of inertial J = 2.26 x 108 m4, outer diameter PS %3D 307.36N, inner diameter P S 384.2 N, Pallowable = 307.36N
Asap handwritten solution acceptable Will definitely upvote I need it immediately
1,200 N-m 4,500 N-m 2,800 N-m 500 N-m (3) 0.70 m 1.80 m 0.70 m Complete the torsion diagram of rod ABCD loaded as shown by dragging the components and filling in the values. T (kNm) A D B 1700 4500 500 -1700 -1200 2800 1600 -2300 -4500 4000 2300 3300 -2800 -3300 1200 -500 -4000 -1600
The rod is supported by smooth journal bearings at A, B, and C and is subjected to the two forces F = 340 N and F2 = 540 N . (Figure 1) Figure < 1 of 1 B. 0.6 m 0.6 m 0.6 m 0.4 m
Question 4 fixed. The shear modulus G and the polar moment of inertia I, of the bar's cross-section are constant along the bar's axis. From the fixed left end (x = 0) of the bar to the middle (x = L/2) of the bar, a lincarly varying distributed torque t, = kr, 0 < x < L/2 is applied (the unit of t, is N-m/m). At the free end (r = L) of the bar, a concentrated torque T is applied (the unit of T is N-m). According to the right-hand rule, the linearly varying distributed torque t, and the concentrated torque T both point to the r-positive direction. Find the angle of twist at the free end (x = L) (Expressing the result with G, Ip, L, T, and k). (Hint: It is easier to find the angle of twist using & = f Figure 1 shows a bar under torsion. The left end of the bar is E.) t, = kx L/2 L/2 Fig. 1. The left end (r = 0) of the bar is fixed, and the right end (r = L) of the bar is applied with a concentrated torque T. A linearly varying distributed torque t, is applied from the left end (z = 0) of…
3. A steel bolt and nut are tightened around an aluminum sleeve. Find the internal forces as the nut is rotated 1 turn (1 turn = 1.5 mm) given the cross sectional areas and the moduli of elasticity for the steel and the aluminum. AST = 150 mm? EST = 200 GPa EAL = 70 GPa AAL = 100 mm? L=150 mm AST Final 1.5 mm Position Al
The shaft is supported at its ends two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T₁ = 410-N forces act in the -z direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and components of force on the shaft. Figure 200 mm 300 mm 150 mm, 150 mm 200 mm 400 mm B 200 N 80 N 80 N 200 N < 1 of 1 Determine the resultant normal force on the cross section at C Express your answer to three significant figures and include appropriate units. Nc= Submit Part B (Vc)y= Submit Part C Value Determine the resultant shear force in the y direction on the cross section at C Express your answer to three significant figures and include appropriate units. (Vc)= = Request Answer 4 ▬▬ μÀ 4 Value Request Answer μÃ → ⒸIE ? Value Units Determine the resultant shear force in the direction on the cross section at C Express your answer to three significant figures and include appropriate units. Ć IE ?…
Determine the torsional shear stress in the shaft section AB and BC. There is a fixed support at C that can resist a moment. (Image taken from Statics and Mechanics of Materials by Beer, Johnson, DeWolf and Mazurek) T₁ = 300 N-m 30 mm TB = 400 N-m 46 mm 055 Shear Stress in AB = Shear Stress in BC= B 0.9 m 0.75 m units: units: