Figure Q7 describes a Linear Feedback Shift Register (LFSR). Draw the equivalent schematic diagram of the system based on an off-the-shelf shift register, clearly showing the number of exclusive-OR gates needed to construct it. LIBRARY ieee; USE ieee.std logic_1164.all; entity lfsr is CLK, RESET: in STD_LOGIC; Q: out STD_LOGIC_VECTOR (5 downto 0) ); port ( end lfsr; architecture behavior of lfsr is begin process (CLK,RESET) begin if RESET='1' then Q <= "000001"; else Q <= ( Q(3) xor Q(2) xor Q(0)) & Q(5 downto 1); end if; end process; end behavior;

Figure Q7 describes a Linear Feedback Shift Register (LFSR). Draw the equivalent schematic diagram of the system based on an off-the-shelf shift register, clearly showing the number of exclusive-OR gates needed to construct it. LIBRARY ieee; USE ieee.std logic_1164.all; entity lfsr is CLK, RESET: in STD_LOGIC; Q: out STD_LOGIC_VECTOR (5 downto 0) ); port ( end lfsr; architecture behavior of lfsr is begin process (CLK,RESET) begin if RESET='1' then Q <= "000001"; else Q <= ( Q(3) xor Q(2) xor Q(0)) & Q(5 downto 1); end if; end process; end behavior;

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Explain how they got the structure of this code?
Explain simply!
Please answer all the questions
Please show all steps/work
Excersize 1: Sketch a schematic of the circuit described by the following VHDL code. Simplify the schematic so that it shows a minimum number of gates. library IEEE; use IEEE.STD_LOGIC_1164.all; entity exercisel is port (a, b, c: in Y, 2: STD LOGIC; out STD LOGIC); end; architecture synth of exercisel is begin y <= (a and b and c) or (a and not b and c); z <= (a and b) or (not a and not b); end; (a and b and not c) or
library IEEE; use IEEE.STD_LOGIC_1164.ALL; entity GCC is Port ( systemClock, reset : in STD_LOGIC; state Output : out STD_LOGIC_VECTOR (4 downto 0)); end GCC; architecture Behavioral of GCC is component FreqDivider is Port (systemClock : in STD_LOGIC; slowClock : out STD_LOGIC); end component; signal nextState, presentState: std_logic_vector(5 downto 0) := "00000"; signal slowClock: std_logic; begin FDO: FreqDivider port map (systemClock => systemClock, slowClock => slowClock); process (slowClock, reset) begin if (reset = '1') then presentState end Behavioral;
Design a 4:1 MUX in multiple ways: a) Using basic gates b) Using tri-state logic c) Using 2:1 MUXes as building blocks as much as possible For each design, write a Verilog implementation and simulate the behavior. Your testbench should exercise all possible combinations of the inputs and selection values.
need help with digital logic
What does map mean?
Create a Test Bench file for the following VHDL code: library IEEE;use IEEE.STD_LOGIC_1164.ALL; entity shiftregister is Port ( R : in STD_LOGIC_VECTOR(5 downto 0); L, w, Reset : in STD_LOGIC; Q : out STD_LOGIC_VECTOR(5 downto 0));end shiftregister; architecture Behavior of shiftregister issignal Sreg : STD_LOGIC_VECTOR(5 downto 0);beginif reset='1' thenSreg <= "000000";elsif clk'event and clk='1' thenif L='1' thenSreg <= R;elseSreg(0) <= Sreg(1);Sreg(1) <= Sreg(2);Sreg(2) <= Sreg(3);Sreg(3) <= Sreg(4);Sreg(4) <= Sreg(5);Sreg(5) <= w;end if;end if;Q <= Sreg;end process;end Behavior;
Explain the following VHDL code module mult_acc input [7:0] ina, inb, input clk, aclr, output [15:0] out endmodule 5.
write a program in C++ using OOP to find the result of following logic circuit: