Fasten the header cover of the cylinder with an inner diameter of 400 mm and an internal pressure of 2 MPa with 16 bolts. 1 Additional load applied to one bolt by internal pressure (P) 2 Assuming that the total fastening force per bolt (Qb) is twice the load (P) applied to one additional bolt by internal pressure, the initial fastening force (Q0) to be applied to the bolt initially 3 Assuming that only tensile force (Qb) is applied to the bolt, the bolt diameter (d1)

Fasten the header cover of the cylinder with an inner diameter of 400 mm and an internal pressure of 2 MPa with 16 bolts. 1 Additional load applied to one bolt by internal pressure (P) 2 Assuming that the total fastening force per bolt (Qb) is twice the load (P) applied to one additional bolt by internal pressure, the initial fastening force (Q0) to be applied to the bolt initially 3 Assuming that only tensile force (Qb) is applied to the bolt, the bolt diameter (d1)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bolted connection shown in figure A uses the friction type connection with 22mm diameter A 325 bolt.(a) Compute the force P required to cause a slip of the 22mm diam. bolt if the slipcoefficient is 0.34 when the section is subjected to a pre-tension load of 174kN(b) Using the force P, compute nominal shear stress.(c) Compute the factor of safety against a slip of a 22mm diam. bolt if the allowable nominal shear is 120MPa. NOTE: SHOW DRAWINGS AND SOLUTIONS.
Give me right solution
1. Please check the safety of bolt connection in the figure below, where F=100KN (design value) and ej=300mm. For the M22 ordinary bolt of grade C, f =140 N/mm? and f" =305 N/mm?. (The unit of length is mm, and ignores the weld mark in the figure.) F %3D 160 b0 オ 80 4=10 |205 4=121 [8 00S
Problem 4.81 The 60-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 20° C. (Figure 1) Figure 1 of 1 -11 100 mm 150 mm Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T2 = 130°C. Express your answer to three significant figures and include the appropriate units. F= Submit HA Value Units My Answers Give Up ? Provide Feedback Continue
20mm Steel Plates in the figure shown are connected by 9 rivets with 20mm diameter. If the Allowable Shear stress for the rivet is 194 MPa and Allowable stress for bearing on the plate is 234 MPa, what is the maximum load P that can be applied in the connection?
Please answer this po, thank you so much!
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
130% v - + 7 Annotate T| Edit Trial expired Unlock Full Version ENGR 263 A A A EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related beams were provided in Chapter 4 as Exercises 4. I through 4.11. These free-body diagrams constitute exercises that will be used here and again in Chapter 12. Follow these instructions carefully to save time later: (a) On each sheet of engineering paper reserved for analysis, calculate the vertical shear specific to that member at appropriate intervals across the length of the free-body diagram. Be sure to solve for locations where shear passes through zero. (b) On cach sheet of engineering paper containing the tree-body diagram, neatly draw the related shear diagram directly below the associated free-body diagram. The shear diagram should be located in the middle one-third of the page. Reserve the bottom one-third of the sheet for the bending moment diagram introduced in Chap- ter 12. Be sure to show…
Don't copy from other experts solution.