ExDoterminereaction420N800 NCómponents atAandB for the beamA Ashown, WeightRollar1.5of the beam is E2 m6oN andthe beamunifor mis CableExThebeamABshown50weighs 10N/msupported byat AB. Delermine The reactwns atandBhinge280 NandCable at4maA and the tensiin in the cable

Given The above figure in ist example with load and their distances and also self weight = 600N

Answered: Ex Dotermine reaction 420N 800 N…

Ex Dotermine reaction 420N 800 N Components at A and B for the beam shown, Weight t Hinge Rollar of the beam is 1.5 2 m 4 m 6od and the beam is uniform

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a.) Solve for FCD b.) Solve for FAC c.) Solve for FCE d.) Solve for RAV
The brass rod AB is fixed connected at A. When the temperature is T₁-50 °C, there is a 3 mm gap between its end (point B) and the wall C. The cross-sectional area of the rod is 10 cm². Ignore the weight of the bar. The temperature is now increased to T₂-130 °C and the rod AB is pushing against the wall at C. Ebr = 100 GPa, abr = 20 x 10-6/°C Fallow 70 MPa L = 3m A 3 m B/C с 3 mm a. Draw a FBD for when the temperature is increased to T₂ and write down the force balance for this scenario. Call the reactions at FA and FC. Ton =1) und prit brolim volgen Aistis Intelesa si s b. State the compatibility condition and solve for the reactions at A and C.
7. Distributed Loads A beam supports a distributed load as shown. (a) Determine the equivalent concentrated load (b) Determine the reactions at the supports. wB = 4500 N/m WA = 1500 N/m %3D A -L 6 m-
A 5.2-m-long aluminum tube (1) is to be connected to a 2.2-m-long bronze pipe (2) at B. When put in place, however, a gap of 9 mm exists between the two members, as shown. Aluminum tube (1) has an elastic modulus of 69 GPa and a cross-sectional area of 1980 mm2. Bronze pipe (2) has an elastic modulus of 93 GPa and a cross-sectional area of 3970 mm2. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses ?1, ?2 produced in each of the members. (b) the displacement (change in length of material (2), up is positive) uB of flange B with respect to support A. 5.2 m 2.2 m Answers: (a) 0₁ = (b) Ug = C (1) B (2) -95.40 1.126 9 mm MPa, 0₂ = mm. -47.58 MPa
Current Attempt in Progress The 445-kg uniform I-beam supports the load shown. Determine the reactions at the supports. -6.3 m- +3.7 m Answers: Ax= i Ay = i By= i Save for Later 340 kg N N N Attempts: 0 of 1 used Submit Answer
18. If a close coiled helical spring absorbs 30 Nmm [S-toof energy while extending by 5mm, its stiffness will be (b) 4 N/mm (a) 2 N/mm sqa-bun ann and (c) 6 N/mm (d) red boxit 10 N/mm q
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
Determine the center of mass in y axis (ỹ) of the homogeneous solid block. L = 0.61m L 3L 1.8 m y 4L 3L - Ancwor:
TWO SOLID CYLINDRICAL RODS ARE JOINED AT B AND LOADED AS SHOWN. ROD AB IS MADE OF STEEL (E = 210 GPa) AND ROD BC OF BRASS (E = 108 GPa). DETERMINE (A) THE TOTAL DEFORMATION OF THE COMPOSITE ROD ABC, (B) THE DEFLECTION OF POINT B. 40 KN 400 mm 600 mm A B C 30 mm 50 KN 50 mm
3) A load of 2,700 N acts on the machine part shown below. The machine part has a uniform thickness of 12 mm. Note: Point H will not be used in this problem and may be disregarded. a) Draw an FBD at showing the internal forces present at K. You may choose which side of the part to cut off. One method means you must find reactions at A and B. Choose the method that seems easier to you. b) Calculate the normal and shear stresses at point K (in MPa). [Ans. to check: = 0; ay = -10.89 MPa; Txy=-6.85 MPa] c) Draw the stress element at the point located at K. d) Calculate the normal and shear stresses if you rotate the element -20°. Draw a properly oriented stress element. 2,700 N 135 mm 60° C 50 mm 75 mm 50 mm X 40 mm # 12 mm 15 mm PH 40 mm OK y
O STATIC M... Find the resultant force of the following? 2 m F = 600 N 3.5 m 0.5 m Fe- 450 N A. 1.5 m 1m 1.5 m 0.5 m y ר
The aluminum rod BC(G=28 GPa) is bonded to the brass rod AB (G= 37 GPa). Each rod is solid and has a diameter of 14 mm. If Tc=30 Nm and Tg= 50 N m, determine the angle of twist at C. 200 mm Brass B Alumimim 300 mm Tc () The magnitude of the intenal reaction torque from A to B is given as TAB= (10) The magnitude of the internal reaction torque from B to C is given as Tec- (N m) (N.m)