Answered: 18. If a close coiled helical spring…

18. If a close coiled helical spring absorbs 30 Nmm Hoof energy while extending by 5mm, its stiffness will be ..... (b) 4 N/mm (a) 2 N/mm sqa-bun tin br (c) 6 N/mm (d) and boxit 107 10 N/mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.58 in. and an elastic modulus of 2430 ksi. Bar (2) has a cross-sectional area of 0.714 in and an elastic modulus of 4110 ksi. Assume Ly-18 in., Lz-47in, Q=6,4 kips, P-3.2 kips, and R-128 kips. Determine the horizontal deflection of end Crelative to end A. (1) Answer: uCA in.
A 5.2-m-long aluminum tube (1) is to be connected to a 2.2-m-long bronze pipe (2) at B. When put in place, however, a gap of 9 mm exists between the two members, as shown. Aluminum tube (1) has an elastic modulus of 69 GPa and a cross-sectional area of 1980 mm2. Bronze pipe (2) has an elastic modulus of 93 GPa and a cross-sectional area of 3970 mm2. If bolts are inserted in the flanges and tightened so that the gap at B is closed, determine: (a) the normal stresses ?1, ?2 produced in each of the members. (b) the displacement (change in length of material (2), up is positive) uB of flange B with respect to support A. 5.2 m 2.2 m Answers: (a) 0₁ = (b) Ug = C (1) B (2) -95.40 1.126 9 mm MPa, 0₂ = mm. -47.58 MPa
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m Sm A B L= 6m 9o kN L-4m A= 0.04 m A = 0.0 6m² E=200 GAa E=80 GPa
Determine whether the truss structures in Fig. 1 are stable or not. 5 kip 5 kip 5 kip Tên TTITT 5 kip 5 kip 5 kip 5 kip 5 kip (a) (b) (c)
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
TWO SOLID CYLINDRICAL RODS ARE JOINED AT B AND LOADED AS SHOWN. ROD AB IS MADE OF STEEL (E = 210 GPa) AND ROD BC OF BRASS (E = 108 GPa). DETERMINE (A) THE TOTAL DEFORMATION OF THE COMPOSITE ROD ABC, (B) THE DEFLECTION OF POINT B. 40 KN 400 mm 600 mm A B C 30 mm 50 KN 50 mm
A simply supported beam, circular in cross section, of span L supports a point load W at mid span. The length of elastic-plastic zone at the plastic hinge will be A 0.33 L B 0.41 L C 0.50 L D 0.58 L
TNT a 8 95% D7:20 Q44 D137 PROBLEM SET NO. 1_STRESS ANALYSIS_SIMPLE STRESS.pdf 1. As shown below, two pneumatic cylinders are used to control the motion and displacement of the device arm ABC. Assuming that the control rods attached at A and D each have a 20-mm diameter and happen to be parallel in the positicn shown. Solve for the average normal stress in (a) member AE, [b) member DG if the applied load at point Cis 800 N. 150 mm G00 m
278. A rigid horizontal bar of negligible mass is connected to two rods as shown in Fig. P-278. If the system is initially stress-free, determine the temperature change that will cause a tensile stress of 60 MPa in the steel rod. -2 m 2 m 3 m 3 m Bronze A-1200 mm² E 88 GPa x = 18.9 pm/(m. °C) Figure P-278. Steel A = 900 mm? E = 200 GFa Q- - 11.7 m/(m. °C)
Problem 3: Inside a steel tube, 2.4 meters long, 34 mm radius, and 1.5 mm thick, 32.5A circular bar made of aluminum with a radius of mm is inserted and these two materials arethey are linked together to form a cross section that will work. This cantilever beam obtained from end Ait is fixedly supported. This cantilever beam,A torque of T = 900 Nm from end B(torque) is applied. Stiffness modulus of steel, Strength= 77 GPa and the stiffness modulus of aluminum Gal = 26Since GPa is the rotation at point BWhat is the (torsion) angle? Calculate.
The solid shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for the aluminum, 83 GPa for steel and 35 GPa for bronze. Aluminum 100 mm -3 m- 4 kN.m Steel 75 mm -2 m 1.5 kN - m Bronze |--15m-l