A compound shaft consisting of a steel segment and an aluminum segment is acte upon by two torques as shown in Fig. P-316. Determine the maximum permissible value of T subject to the following conditions: Tst ≤ 83 MPa, Tal ≤ 55 MPa, and the angle of rotation of the free end is limited to 6°. For steel, G = 83 GPa and for aluminum, G = 28 GPa. Steel OT Al

A compound shaft consisting of a steel segment and an aluminum segment is acte upon by two torques as shown in Fig. P-316. Determine the maximum permissible value of T subject to the following conditions: Tst ≤ 83 MPa, Tal ≤ 55 MPa, and the angle of rotation of the free end is limited to 6°. For steel, G = 83 GPa and for aluminum, G = 28 GPa. Steel OT Al

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two shafts are made of A-36 steel. Each has a diameter of 21 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B. They are also supported by journal bearings at C and D, which allow free rotation of the shafts along their axes. A torque of 500 Nm is applied to the gear at E as shown in the figure below. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Figure 50 mm 100 mm 1.5 m B 1 of 1 0.75 m 500 N-m Part A Determine the rotation of the gear at E. Express your answer using three significant figures. OF AΣo↓ vec PE=0.02897 Submit Previous Answers Request Answer Provide Feedback X Incorrect; Try Again; 8 attempts remaining ? rad
A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of diameter 50 mm. 2GB) Both shafts are firmly (Gs jointed. The combined assembly is subjected to a torque of 1000 Nm. calculate maximum shear stress = developed in steel in N/mm2 (up to 2 decimals)
Problem 3: Put 32.5 into a steel tube 2.4 meters long, 34 mm radius and 1.5 mm thick. A circular bar made of aluminum with a radius of mm is inserted and these two materials are they are linked together to form a cross section that will work. This cantilever beam obtained from end A it is fixedly supported. This cantilever beam, A torque of T = 900 Nm from end B (torque) is applied. Stiffness modulus of steel, Ge 2.4 m 77 GPa and the modulus of stiffness Gal = 26 for aluminum Since GPa is the rotation at point B What is the (torsion) angle? Calculate.
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
An aluminum tube of outer diameter R, - 50 mm is heated such that it is mounted over a steel shaft of radius, R, = 20 mm as shown in the figure The length I of the member is 3 m. MT R2 Ri If a G, -77.2 GPa, G2 = 27 GPa, and torque of M- - 36 kN.m is applied to induce twisting in the member, Calculate the torque acting in the steel shaft
Som.
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of tapered rod 2 (in mm). Indicate negative sign if compression. 5P 3P E-10 GPa E-200 GPa 80mm 3o mm 30 mrm 80 mm 30 mm 30 m
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P-7 kN, Determine the axial deformation of tapered rod 2 in mm). Indicate negative sign if compression. 5P 3P E-200 GP Bomm o mm se mm 60 mm 80 mm 30 mn Next
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P= 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. e 5P 39 E-200 GP gomm 30 mm 30 mvm 80 mm 30 mm 30 mm
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. 5P E-10 GPa + 39 E-200 GPo 3M 80mm 30 mm 30mm 80 mm 30 mm 30 mm