Each of the four vertical links has an 8 X 36-mm uniform rectan- gular cross section, and each of the four pins has a 16-mm diameter. Determine the maximum value of the average normal stress in the links connecting (a) points B and D, (b) points C and E. 0.4 m 0.25 m 0.2 m 20 kN A B

Q: Problem: Determine the maximum shearing stress developed in each material. Also, determine the…

A:

Q: The truss shown consists of wooden members. Knowing that each member has a 75 x 75 mm. square…

A:

Q: 2. The major and minor principal stresses at the point are 3 MPa and -3 MPa respectively The maximum…

A: To find out the maximum shear stress at the point.

Q: 50 ft and b = 5.40 ft. If the normal stress in each member must not exceed 35 ksi, determ upported…

A:

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A:

Q: 24. A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A:

Q: Each of the four vertical links has an 8 X 36-mm uniform rectan- gular cross section, and each of…

A:

Q: Q.17 The maximum bending stress is 0039 A w/m m L P Od

A:

Q: -150 mm B - 300 mm 30°

A:

Q: 1.0 m 3.3 m A simple pin-connected truss is loaded and supported as shown. All members of the truss…

A:

Q: A B 400 mm 500 mm 20 mm 40 mm 7 kN/m 3 m 20 kNm 2.5 m 2.5 m 2 m 15 KN A T-beam with the…

A: Given Data Determine  a. Second moment of area of cross section.  b. Draw the SFD and BMD.  c.…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A: GIVEN DATA:-⇒a = 4.25 ft⇒b = 5.10 ft⇒A = 2.1 in2⇒σ = 35 ksi

Q: The truss shown consists of wooden members. Knowing that each member has a 50 x 50 mm square…

A: Determine the maximum value of the average normal stress in (a) in member BD, (b) in member DE.

Q: Problem 2. Two rods connected at B are restrained at points A and C. The section AB is steel and E,…

A: Given,Es=200GPa Alpha s=12.3×10-6/℃ Eb=100GPa Alpha b=21.5×10-6/℃ ∆T=70℃ Dab=50mm Lab=200mm Dbc=70mm…

Q: Link AC has a uniform rectangular cross section 3 mm thick and 12 mm wide. Determine the normal…

A: Given: Link AC: thickness= 3mm, Width=12mm

Q: The member shown has a rectangular cross section, determine the state of stress that loading…

A:

Q: 8 kN/m 35° E By D 20 kN 0.4 m 0.4 m 0.4 m

A:

Q: 5 kN is distributed equally among the three rivets, fi e bearing stress between a plate and a rivet;…

A: Given data Diameter, d=25mm Load, P=75kN Thickness, t=25mm The expression for area is given as…

Q: -57. Determine the principal stress, the maximum in-plane shear stress, and ver 120 MPa MADARAKAN…

A: Given data : The value of normal stress in X direction σX=300 MPa The value of normal stress in Y…

Q: Note: Dont truncate the solution Find the absolute value of the axial stress in member AC and BE of…

A: To find stress in member AC, BE

Q: Link AB is to be made of a steel for 15 kN/m which the ultimate normal stress is 30° 400 MPa.…

A:

Q: A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in…

A:

Q: The lap joint is connected by 3-20mm diameter rivets. Assuming that the axial load P = 50 kN is…

A:

Q: diameter of the smallest pin that can be used if not to exceed a shear stress of 60 MPa (Draw

A:

Q: 3) Find a) the maximum stress in the shown member, b) the relative displacement between 8 and D (Ap)…

A:

Q: Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses…

A:

Q: Member AC is subjected to a vertical force of 3 kN. Cross sectional area of tie rod is 400 mm? and…

A:

Q: For the assembly shown below, bar AB is loaded with P at its midspan. a.) If P = 10 kN, compute the…

A: Shearing Stress is the type of stress that acts coplanar with a cross-section of material. It occurs…

Q: Q.17 The maximum bending stress is 0039 A w/m m L P Od

A:

Q: a b 45 MPa 60° a

A: Given: Shear stress  To find: Normal stress and principal stress on inclined plane

Q: Q.17 The maximum bending stress is A w/m L P Ond

A:

Q: Determine the maximum shearing stress developed in each segment. For bronze, G = 36 GPa; aluminum, G…

A:

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: In the following structure, consider the following data: The connection at D is double and has a…

A:

Q: The maximum tension in the INwer link of a Porter governor is 580 N and the maximum stress in the…

A: Given data in question  Stress Load To find out  Diameter

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.