Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa

Q: 3 N/m 8cm a-2 cm I m im

A: Draw the given figure

Q: Punch Aluminum =4 mm d-20 mm

A: Given that  t=4 mmd= 20 mmUltimate shear stress = 280 Mpa

Q: Determine maximum principal stress

A: Given data : Normal stress in X direction σX=-320 MPa Normal stress in Y direction σY=240 MPa Shear…

Q: : Determine the state of stress at point A on the cross section of the member at section a-a. 600 N…

A:

Q: The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part…

A:

Q: What is the stress at the section x - x. for the bar ABCD with uniform cross-section 1000 mm²? с A…

A:

Q: Explam how the total stess at a distance z be determined from the figure below Com ground surface…

A: For multi layered soil Total stress is given by :σt=∑ γtγ=unit weightst=thickness of each layer

Q: For the figure below, Determine the following: 10 MPa - 40 MPa 50 MPa The oavg is equal to in MPa:…

A: Max shear stress occurs when there is a concentrated shear force in a small region. As the normal…

Q: Find maximum principal stress

A: Given data : The value of normal stress in X direction σX=560 MPa The value of normal stress in Y…

Q: Question 6 of 15 The plate of thickness, t = 5 mm, is loaded with the following stress; o, =100 MPa,…

A:

Q: Find maximum principal stress

A: Given data : The value of normal stress in X direction σX=-30 MPa The value of normal stress in Y…

Q: Determine the stress in rod if tensile force applied of 35 N having cross sectional area of 50 mm2

A: Given  Tensile force F= 35 N Crossectional area A= 50 mm2

Q: a) The principal planes b) The principal stresses c) The stress components exerted on the element…

A: Question is based on the element subjected to axial, compression and shear stress .  Magnitude of…

Q: Link AB is to be made of a steel for 15 kN/m which the ultimate normal stress is 30° 400 MPa.…

A:

Q: ABD rigid bar with 40mm diameter BC bar at point B, It is supported from point A with a 30 mm…

A:

Q: Explain in detail how you will carry out surveying of agriculture field using chain surveying.…

A: (a) The chain survey is used to measure the distance between two points.  The instruments required…

Q: Maximum principal stress

A: Given data : The value of normal stress in X direction σX=55 MPa The value of normal stress in Y…

Q: Q- The normal stresses on the two mutually perpendicular planes at a point are 120 MPa (Tensile) and…

A:

Q: 700 kPa 4 MPa 40 MPa 600 kPa (a) (b) (c)

A:

Q: Determine maximum and minimum principal stress

A: Given data : Normal stress along X axis (σX)=-560 MPaNormal stress along y axis (σY)= 250 MPaShear…

Q: Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if…

A:

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: Determine the largest torque Tmax that can be applied at the upper end of the steel rod.

Q: 40 MPa 35 MPa 60 MPa

A:

Q: Q- The normal stresses on the two mutually perpendicular planes at a point are 120 MPa (Tensile) and…

A:

Q: Determine the normal stress (in Mpa) in member AC of the truss shown if it is made up of a…

A:

Q: (d) Determine the maximum in-plane shear stress. 10 ksi 16 ksi

A: This question is related to Principal Stresses from Strength of Material. In this question we…

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: b 7'

A:

Q: 02: For the stresses at the point shown, find: • The maximum shearing stress. • The principal…

A:

Q: Determine the maximum stress of the plate.

A: Given, Width of plate,b= 7 cm= 70mmRivet hole diameter,d= 2 cm = 20 mmFind the maximum stress of the…

Q: The bronze bar 3.00 m long with a cross-sectional area of 350 mm is placed between two rigid walls.…

A:

Q: The maximum and minimum normal stresses is known as?

A: The combination of normal and shearing stresses acting on two mutually perpendicular planes is…

Pressure and Stress