Each branch of a three-phase star-connected load consists of a coil of resistance 4.2 Ω and reactance 5.6 Ω. The load is supplied at a line voltage of 400 V, 50 Hz. The total active power supplied to the load is measured by the two-wattmeter method. Draw a circuit diagram of the wattmeter connections and calculate their separate readings. Derive any formula used in your calculations. ANS: 13.1 kW, 1.71 kW

Each branch of a three-phase star-connected load consists of a coil of resistance 4.2 Ω and reactance 5.6 Ω. The load is supplied at a line voltage of 400 V, 50 Hz. The total active power supplied to the load is measured by the two-wattmeter method. Draw a circuit diagram of the wattmeter connections and calculate their separate readings. Derive any formula used in your calculations. ANS: 13.1 kW, 1.71 kW

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

5 kVA at 60 Hz Primary 2400 V ellele Secondary Given the transformer in Volts rms, what is the maximum theoretical 120 V current rating of the Secondary (in Amps rms)? Select one: OA. 2.08 A OB. 12.78 A OC. 25.4 A OD. 41.67 A
Determine the apparent power, active power and reactive power in a series circuit, when the supply voltage is 75 Volt, the current is 1 Amp and the phase angle is 30 lagging. Also, draw a power triangle for the circuit.
Q1. The three-phase full-wave converter in Figure shown is operated from a three phase Y-connected supply. Sketch the output voltages appeared at the load for firing angle 15°. I need Sketch an Ven จ T1 Q Yi₁ = I₂ a ia = is T₁ T3 T₂ Vbn b ib Load Highly inductive load ▲ T6 T₂ iT4 On T5, T6 T6, T₁ T2, T3 T3, T4 T4, T5 T5, T6 ཅ 0 T₁ الاسم T₁ Is wt
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
Please answer question in image with details on how to do it. Thank you.
1) Determine the total current supplied by the source and the current in each branch. 2) Sketch a fully labelled phasor diagram showing all voltage and currents in the circuit. 3) Determine the active power delivered by the source voltage. 4) Determine the reactive power. 5) Sketch the power triangle. 6) Comment on the significance of the power factor and briefly state how it can be improved.
5. A power-supply transformer has a secondary voltage if the primary is connected to a 120 V rms source? 6. Determine the peak and average power delivered to RL in figure. turns ratio of 5:1. What is the 2:1 120 V rms 220 N ell lelll
A parallel circuit of 25 – ohm resistor, 64 – mH inductor and 80 - μF capacitor connected across a 110 V, 50 Hz, single phase supply is shown in the figure below. Calculate: a.) the current in the individual element, b.) the total current drawn from the supply, c.) overall power factor of the circuit. Draw a neat phasor diagram showing IR, IL and IC.
helpp
The temperature of a noninductive heater unit is controlled by a reactor. The heater unit and the reactor are connected in series across a 250 V, 60 Hz source. The voltage across the heater unit is 200 V. The voltage across the reactor is 100 V. The current in the circuit is 10 A. Determine: the power factor of the series circuit. the power factor of the reactor. the impedance of the reactor. the effective resistance of the reactor. the inductive reactance of the reactor
Problem: Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Neglect Rsurge- Rurpe 120 V ms 10N 100 uF 33 kn Express the numerical values up to 2 decimal places. Vr(pp) = Vpp Vdc = V lll lell
An RL series circuit is connected to a 60-Hz, 208-volt power line. A clamp-on ammeter indicates a current of 18 amperes. The inductor has a reactive power of 1860 VARs. a. Draw the schematic diagram. b. Compute the impedance. c. What is the value of L? d. What is the value of R? e. Find the power factor..