7:50ul LTE OA docs.google.comChoose the correct answer *During the tensile test, experiment on a sample of mild steel, data represented in thefigure below was obtained with an initial diameter (do) of 0.505 inch. At failure, thereduced diameter (d) of the sample was 0.305 inch. Gauge Length (Lo) is 2 inchesand final Gauge Length (L,) is 2.625 inches. Answer the questions below:Us70TkLyPIR50-FLPL ptiel linitAL or 6TPEL lastie liiUP per yied paintLypi Lewer sus t uni mated streagthIR: Indicatul sireghRuptureTR True strugth RuplefPL (propartimal timt)Direct strain& totoE strmin Cin/in)ab1. Mild steelis: (a) brittlematerials (b)ductilematerial (c)between theductile andthe brittle2. Young'sModulusevaluateselasticitywithin theregion from:(а) 0 -ProportionalLimit. (b)ProportionalLimit - Loweryield Point.(c) Lower

Given, d0=0.505 inchdf=0.305 inchL0= 2 inchesLf=2.265 inches

During the tensile test, experiment on a sample of mild steel, data represented in t figure below was obtained with an initial diameter (do) of 0.505 inch. At failure, th reduced diameter (d,) of the sample was 0.305 inch. Gauge Length (Lo) is 2 inche and final Gauge Length (L,) is 2.625 inches. Answer the questions below: Ge Le LyP PL pti lit EL lasti d uP er yied peint t i reg Indieatul singh Rupture "Te Th serati Ra 40 AL or 8 PL rertimal tat) us ui Direct strain A Lo E simin (in/in) a 1. Mild steel is: (a) brittle materials (b) ductile material (c) between the ductile and the brittle 2. Young's Modulus evaluates elasticity within the region from: (a) 0 - Proportional Limit. (b) Proportional Limit - Lower yield Point. (c) Lower a Stress Iblint (PST

During the tensile test, experiment on a sample of mild steel, data represented in t figure below was obtained with an initial diameter (do) of 0.505 inch. At failure, th reduced diameter (d,) of the sample was 0.305 inch. Gauge Length (Lo) is 2 inche and final Gauge Length (L,) is 2.625 inches. Answer the questions below: Ge Le LyP PL pti lit EL lasti d uP er yied peint t i reg Indieatul singh Rupture "Te Th serati Ra 40 AL or 8 PL rertimal tat) us ui Direct strain A Lo E simin (in/in) a 1. Mild steel is: (a) brittle materials (b) ductile material (c) between the ductile and the brittle 2. Young's Modulus evaluates elasticity within the region from: (a) 0 - Proportional Limit. (b) Proportional Limit - Lower yield Point. (c) Lower a Stress Iblint (PST

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A tensile test is performed on a brass specimen 10 mm indiameter using a gage length of 50 mm. When the tensile load Preaches a value of 20 kN, the distance between the gagemarks has increased by 0.122 mm. a) What is the modulus of elasticity E of the brass? b) If the diameter decreases by .00830 mm,what is Poisson's ratio? 10mm PO 50mm. P
ngineering / Civil Engineering / Q&A Library/1 a. a. During a tensile test on a speci... 1 a. During a tensile test on a specimen the following results were obtaineo Load (kN) 15 30 40 50 55 60 Extension 1.03 2.00 2.73 3.42 3.80 4.10 (mm) Diameter at fracture -16.5mm Diameter of gauge length =19mm Gauge length = 150mm Load at fracture - R0KN Gauge length at fracture = 170mm Ultimate load-120kN Plot the load/extension graph to an appropriate scale. Hence determine the i. Modulus of elasticity ii. Percentage elongation iii. Percentage reduction in area iv. The nominal stress at fracture
need help
Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was obtained from the test : (i) Diameter of the steel bar (ii) Gauge length of the bar (iii) Load at elastic limit (iv) Extension at a load of 150 kN. (v) Maximum load (vi) Total extension (vii) Diameter of the rod at the failure Determine : (a) the Young's modulus, = 3 cm = 20 cm = 250 kN = 0.21 mm = 380 kN = 60 mm - 2.25 cm. (c) the percentage elongation, and (b) the stress at lastic limit, (d) the percentage decrease in area.
2 please include scketch
0.9
A brass alloy rod having a cross sectional area of 100 mm2 and a modulus of110 GPa is subjected to a tensile load. Plastic deformation was observed tobegin at a load of 39872 N.a. Determine the maximum stress that can be applied without plasticdeformation.b. If the maximum length to which a specimen may be stretched withoutcausing plastic deformation is 67.21 mm, what is the original specimenlength?
8.
Show the complete and organize solution. Write your answer with four decimal places and enclose them in a box. Solve as neatly as possible thank you! ANSWER ONLY A AND B
The data shown in the table were obtained from a tensile test of a metal specimen with a rectangular cross-section of 0.2 in.^2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches.
I need correct answer
A drill rod with a diameter of 10 mm is made of high-strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 90° with respect to the other end without exceeding an allowable shear stress of 300 MPa?