gineering / Civil Engineering/ Q&A Library /1a. a. During a tensile test on a speci... l a. During a tensile test on a specimen the following results were obtainc. Load (kN) 15 30 40 50 55 60 Extension (mm) 1.03 2.00 2.73 3.42 3.80 4.10 Diameter of gauge length =19mm Gauge length = 150mm Load at fracture- 80KN Diameter at fracture -16.Smm Gauge length at fracture - 170mm Ultimate load-120KN Plot the load/extension graph to an appropriate scale. Hence determine the i Modulus of elasticity ii. Percentage elongation iii. Percentage reduction in area iv. The nominal stress at fracture

gineering / Civil Engineering/ Q&A Library /1a. a. During a tensile test on a speci... l a. During a tensile test on a specimen the following results were obtainc. Load (kN) 15 30 40 50 55 60 Extension (mm) 1.03 2.00 2.73 3.42 3.80 4.10 Diameter of gauge length =19mm Gauge length = 150mm Load at fracture- 80KN Diameter at fracture -16.Smm Gauge length at fracture - 170mm Ultimate load-120KN Plot the load/extension graph to an appropriate scale. Hence determine the i Modulus of elasticity ii. Percentage elongation iii. Percentage reduction in area iv. The nominal stress at fracture

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel specimen is tested in tension. The specimen is 1" wide by 0.5" thick in the test region. By monitoring the stresses from the testing machine, it was found that the specimen yielded at a stress of 72 ksi and fractured at 96 ksi. (a). Determine the tensile loads at yield and at fracture
In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P- 30 kN. Knowing that E- 70 GPa, and the change in diameter of the rod- 0.00955 mm, determine the poissons' ratio v. 20n diateter gage length-150 0.33 O 0.6 0.29 O 0.35
This figure shows typical stress-strain behaviour for a brass. The inset figure shows the behaviour at low strains. 500 70 Tosle strength 450 MPa 166,000 ps 60 400 300 MP 40 30 200 Yeld steg 250 MPa (,0a 200 20아 100- 20 100 10 0.20 030 040 If the cylindrical test sample is initially 14cm long with an initial radius of 2mm, estimate the true stress in MPa at the ultimate tensile stress. (Enter your answer to the nearest whole number) an es
A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. Determine the yield strength (σy) at a strain offset of 0.002.
A steel specimen is tested in tension. The specimen is 25 mm wide by 12.5 mm thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 160 kN and fractured at 214 kN. a. Determine the tensile stress at yield and at fracture. b. If the original gauge length was 100 mm, estimate the gauge length when the specimen is stressed to 1/2 the yield stress.
A steel specimen is tested in tension. The specimen is 2 in. wide by 2.3 in. thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 30 kips and fractured at 40 kips. a) Determine the tensile stress at yield and fracture; b) If the original gauge length was 4 in., estimate the gauge length when the specimen is stressed to 2 the yield stress.
A 50 mm diameter steel hanger rod carries an axial load of 271 kilonewtons. Under this load, it's average unit strain is 0.00069. determine the modulus of elasticity for the steel.
A steel specimen having a modulus of elasticity equal to 29x103ksi has a width of 1.0in and thickness of 0.25in. During the tensile strength testing, the specimen yielded at 12.5kips and fractured at 17.5 kips. Compute the value of the tensile stresses at yield and fracture
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
7) A specimen of steel 20 mm diameter with a gauge length of 200 mm is tested to destruction. It has an extension of 0.25 mm under a load of 80 kN and the load at elastic limit is 102 kN. The maximum load is 130 kN. The total extension at fracture is 56 mm and diameter at neck is 15 mm. Find (i) The stress at elastic limit. (ii) Young's modulus. (iii) Percentage elongation. (iv) Percentage reduction in area. (v) Ultimate tensile stress.
Given: metal specimen x-section (circular) = 0.5sin Gaye length Fractured final final diameter Determine ^ = 2.030 In occured at 28, 500 # length = 2.30in dia = 0.43 in al Ultimate b7 Elongation c) Reduction tensile stress in ksi a percentage as of x-section area as a percentage
A steel bar of 22 mm diameter and 8 cm gage length was axially loaded in tension and the following load deformation diagram was obtained. Determine: a) The yield strength by 0.2% off-set method. b) Modulus of elasticity by initial tangent method. c) Modulus of elasticity by tangent method at 2/3 of the yield strength. d) Modulus of elasticity by secant method at 70% of ultimate strength. e) Strain in fracture.