A tensile test specimen of stainless steel alloy having a diameter of 0.550 in. and a gage length of 2.5 in. was tested to fracture. Stress and strain data obtained during the test are shown in the Figure Determine: (a) the modulus of elasticity. (b) the proportional limit. (c) the ultimate strength. (d) the yield strength (0.20% offset). (e) the fracture stress. Stress (ksi)

A tensile test specimen of stainless steel alloy having a diameter of 0.550 in. and a gage length of 2.5 in. was tested to fracture. Stress and strain data obtained during the test are shown in the Figure Determine: (a) the modulus of elasticity. (b) the proportional limit. (c) the ultimate strength. (d) the yield strength (0.20% offset). (e) the fracture stress. Stress (ksi)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

This figure shows typical stress-strain behaviour for a brass. The inset figure shows the behaviour at low strains. 500 70 Tosle strength 450 MPa 166,000 ps 60 400 300 MP 40 30 200 Yeld steg 250 MPa (,0a 200 20아 100- 20 100 10 0.20 030 040 If the cylindrical test sample is initially 14cm long with an initial radius of 2mm, estimate the true stress in MPa at the ultimate tensile stress. (Enter your answer to the nearest whole number) an es
1) The stress-strain tests were carried out on five different metals (A, B, C, D and E) and the results are shown in the figure below. Select the metal for given properties. E B Strain Metal Property (А, В, С, D or E) Highest resistance i. to plastic strain Lowest stiffness Highest ductility Highest brittleness Highest tensile strength Lowest fracture strength ii. iii. iv. v. vi.
A structural component in the shape of a flat plate 24.3 mm thick is to be fabricated from a metal alloy for which the yield strength and plane strain fracture toughness values are 533 MPa and 22.0 MPa-m1/2, respectively. For this particular geometry, the value of Y is 1.3. Assuming a design stress of 0.4 times the yield strength, calculate the critical length of a surface flaw. What formulas do i use ? And how do i use them?
A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. Determine the yield strength (σy) at a strain offset of 0.002.
A steel specimen is tested in tension. The specimen is 25 mm wide by 12.5 mm thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 160 kN and fractured at 214 kN. a. Determine the tensile stress at yield and at fracture. b. If the original gauge length was 100 mm, estimate the gauge length when the specimen is stressed to 1/2 the yield stress.
A steel specimen is tested in tension. The specimen is 2 in. wide by 2.3 in. thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 30 kips and fractured at 40 kips. a) Determine the tensile stress at yield and fracture; b) If the original gauge length was 4 in., estimate the gauge length when the specimen is stressed to 2 the yield stress.
The information in the photo attached shows elastic properties of a human tibula bone. If you were to take a small cuboidal cross section of the tibula bone and apply the ultimate shear stress, what would be the resulting strain? (a) 1.0 % (b) 6.7 % (c) 10 % (d) 15 % (e) None of the above.
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
A steel specimen having a modulus of elasticity equal to 29x103ksi has a width of 1.0in and thickness of 0.25in. During the tensile strength testing, the specimen yielded at 12.5kips and fractured at 17.5 kips. Compute the value of the tensile stresses at yield and fracture
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
The stress-strain tests were carried out on five different metals (A, B, C, D and E) and the results are shown in the figure below. Select the metal for given properties. Stress L ii. iii. iv. V. vi. B Strain Property Highest resistance to plastic strain Lowest stiffness Highest ductility Highest brittleness Highest tensile strength Lowest fracture strength Metal (A, B, C, D or E) N
3-3. Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Plot the diagram, and determine approximately the modulus of toughness. The rupture stress is or = 53.4 ksi.