A drill rod with a diameter of 12 mm is made of high- strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 900 with respect to the other end without exceeding an allowable shear stress of 300 MPa?

A drill rod with a diameter of 12 mm is made of high- strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 900 with respect to the other end without exceeding an allowable shear stress of 300 MPa?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A drill rod with a diameter of 1/2 in. is made of high-strength steel alloy with a shear modulus of 11.6 * 106 psi. The rod is to be subjected to a torque T.What is the minimum required length L of the rod so that the cross section at one end can be rotated 60° with respect to the other end without exceeding an allowable shear stress of 45 * 103 psi?
A plate of 150 mm width and 20 mm thick is welded to another plate by fillet weld as shown in figure below. The size of the weld is 12 mm throughout. Compute the average shear stress produced in the weld for the full strength of the plate if the allowable stress is 150 N/mm². 70.72 mm T 50 mm 1 ㅅ 70.72 mm 150 mm- -150 mm -60 mm dia T 150 mm
A plate of 150 mm width and 20 mm thick is welded to another plate by fillet weld as shown in the figure. The size of the weld is 12 mm throughout. Compute the average shear stress produced in the weld for the full strength of the plate if the allowable stress is 150 N/mm². 70.72 mm 70.72 mm 14 150 mm 150 mm ► 60 mm dia 150 mm
The inner and outer diameters of a hollow cylindrical steel are 10mm and 15mm, respectively. It is 1 m long. a) What is the maximum applicable torque such that the shear stress on the shaft does not exceed 100mpa? b) What is the corresponding minimum shear stress value in steel?
Correct solution & don't copy
A copper rod of length L = 18.0 in. is to betwisted by torques T (see figure) until the angle ofrotation between the ends of the rod is 3.08.(a) If the allowable shear strain in the copper is0.0006 rad, what is the maximum permissiblediameter of the rod?(b) If the rod diameter is 0.5 in., what is theminimum permissible length of the rod?
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
Can you solve it please? Thank you A mild steel specimen having Young’s modulus of 200 GPa and original length of 300 mm is tested for a stress of value 500 MPa. Find the resultant elongation in the specimen.
Engineering Mechanics. please help to provide solution for the this problem.
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?