diam. pipe through which water flows at the rate of If the axis of vertical tube А 0.3 0.283 m°/s suddenly enlarges to 0.6 m in diam. the pipe ils horizontal and the water in a connected to the larger pipe stands 0. 36 higher than the level in coefficient K if the shock loss is expressed as KV*/2g, where v is the velocity in the smaller pipe. 8. pipe, determine the a tube connected to the smaller

diam. pipe through which water flows at the rate of If the axis of vertical tube А 0.3 0.283 m°/s suddenly enlarges to 0.6 m in diam. the pipe ils horizontal and the water in a connected to the larger pipe stands 0. 36 higher than the level in coefficient K if the shock loss is expressed as KV*/2g, where v is the velocity in the smaller pipe. 8. pipe, determine the a tube connected to the smaller

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given: Asked: Solution:
The man shown in (Figure 1) blows air through the 3-mm diameter straw with a velocity of 2.8 m/s. Assume fully developed flow occurs along the straw. The temperature of the air is 20°C. Figure -225 mm- 1 of 1 > T Part A Determine the force his lips exert on the straw to hold it in place. Express your answer using three significant figures and include the appropriate units. P-6.673 HA Provide Feedback N ? ubmit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining
Water is pumped from the upper reservoir to the lower reservoir through the piping system shown. Determine the power required for the pump if the water flow rate is 60 kg/s. The fittings from pipe Di to pipe D2 and from pipe D2 to pipe D3 can be considered to be standard 90° elbows with velocity in pipe 2 for the friction loss. Data: h = 10 m, h2 = 3 m, L1 water viscosity = 1 cP = 103 kg/m-s, p= 1000 kg/m³. The pipe roughness is 0.05 mm. The pump efficiency is 75%. 50 m, L2 = 300 m, L3 = 2 m, D¡ = 0.2 m, D2= 0.5 m, D3 = 0.03 m, (1) D,, L, D2, L, Globe valve D3, L,
Question 3 Water (p = 1000 kg/m³, μ = 1.12 x 10-3 Ns/ m²) flows through a 0.01-m-diameter pipe at a velocity of 2 m/s. The length of the pipe is 40 m. A pump is used to maintain the flow from one reservoir to another reservoir as shown. The following data are available: KL elbow = 1.5, Kentrance = 0.5, Kexit = 1.0. Elbow Pump Elbow Figure Q1 Note that the entrance and exit are at the same elevation. The free surfaces of the reservoirs are also at the same elevation. (a) Calculate the total head losses in the pipe.
A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted through the pipe in which water having a pressure of 490.5 N/cm2at inlet is flowing. If the pressure drop over the length of pipe is 98.1 N/cm2and ff = 0.0065.Determine:The diameter of the pipe and the volume flow rate; and If a nozzle is introduced at the end of the pipe, what would be its diameter and the power transmitted.
The properties of the air in the inlet section with A1 = 0.2562 m2 in a converging-diverging channel are given as U1 = 256,2 m/s, T1 = 362 K, P1 = 136,2 kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
answer first item only
Provide a detailed solution
(a) Prove that the loss of pressure head for the viscous flow through a circular pipe is given by h.
A horizontal smooth-walled cylindrical pipe has diameter 0.04 m. Water flows along the pipe with a flow rate of Q 2 x 10-4 m³ s-¹. = For water, take the kinematic viscosity as v = 10-6 m² s¹ and the 10³ kg m-³. density as p = (a) Calculate the Reynolds number and establish whether the flow is turbulent or not. (b) Show that λ = 0.035 is a good approximation of the Darcy friction factor for this flow. (c) Calculate the shear stress at the wall of the pipe, and hence find the magnitude of the drag force exerted by the water on a length 2 m of the pipe. L =
7. For the flow of a thin layer of liquid down an inclined plane shown: a. Using the cross-hatched element and through a force balance, show that the velocity distribution across the layer is: dx Y sin e (b2 – s2) 2 µ и 3 Free Surface an expression for the at the free b. Derive t dx liquid velocity surface. c. Derive an discharge per unit width. d. Derive Fixed y s dx expression for the Wall b an expression for the shear stress at the fixed wall.
A syringe is used to deliver vaccine against an infectious disease. This particular syringe is not perfect so it is expected that 5% of the vaccine flow rate out of the needle will leak past the plunger. The area of the plunger is 400mm?. If the vaccine has to be injected steadily with the flow rate of 250 cm³/min, sketch the control volume and determine the speed at which the plunger should be moved.