Q.2) Air flows through a circular duct (D=0.4 m) at a velocity of 4 m/s, determine the pressure drop that occurs over a 6-m length of the duct. The friction factor is f = 0.0005. Take pair= 1.2 kg/m³. 0 31 JAG 100 10.30

Q.2) Air flows through a circular duct (D=0.4 m) at a velocity of 4 m/s, determine the pressure drop that occurs over a 6-m length of the duct. The friction factor is f = 0.0005. Take pair= 1.2 kg/m³. 0 31 JAG 100 10.30

Name: Q.2) Air flows through a circular duct (D=0.4 m) at a velocity of 4 m
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q.2) Air flows through a circular duct (D=0.4 m) at a velocity of 4 m/s, determine thepressure drop that occurs over a 6-m length of the duct. The friction factor is f =0.0005. Take pair= 1.2 kg/m³.031400503

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a 12" diameter pipe carries oil with a velocity distribution of v = 9(r1^2 - r^2) determine the average velocity and the value of kinetic energy correction
A cast iron pipe is to convey oil with specific gravity of 0.9 and a viscosity of 0.00384 Pa-s from one tank to another at a rate of 14 L/s. If the If the diameter of the pipe is 2.75 m, find the Friction factor. Relative roughness is 0.001.
A given centrifugal pump works at a flow coefficient Cf=0.65 The pump has a diameter of 3.0 cm and a the out surface 1.3 cm^2 and runs at rotation speed of 800 rpm What is the actual flow rate? give you answer in Liter/min Your Answer: Answer units
Please answer quickly. Thanks
Compute the Cross sectional area of Pipe Discahrge=0.8 m3/s Velocity=2 m/s
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft3/s. a. H = 51 + 25.98(Q^2) b. H = 54 + 24.98(Q^2) c. H = 54 + 25.98(Q^2)
I ll rate
find the diameter through circular duct if the flow rate (0.98 m3/s) and velocity(5m/s) Fulleen Snip 280 mm 490 mm 560 mm 750 mm 820 mm
Question 6 Determine the velocity of flow and the friction loss as 0.472 m3/s of air flows through 23 m of an 0.305 m-diameter round duct V=6.5 m/s and DeltaP=41.5 Pa V=15.3 m/s and DeltaP=117.5 Pa V=9.3 m/s and DeltaP=94.3 Pa V=6 m/s and DeltaP=11 Pa
my last Id 30 Water mass flow rate of 2kg/s is delivered through the 30 mm commercial steel pipe? -0.15 Calculate the miner and friction losses in the pipe. Use moody chart to calculate the friction loses For minor losses, take K for the Entrance: 0.3 Exit: 0.5 Valve 1.8 Water density: 1000 kg/m? Water viscosity : 0.001 N. S/ m² Use your last three digits of your ID number for the pipe length L_in m h-20 m Gate valve
For a pipe flow Reynold number is found to be 54000. What is the coefficient of friction of the pipe? O a. 5.18 x 10 O b.2.96 O c 5.18 O d. 2.96 x 10
The Darcy friction factor for both of the pipes shown is 0.024. the total flow rate is 300 m3/h. what is the flow rate through the 250 mm pipe. 325 m, 150 mm diameter a= 300 m/h 650 m, 250 mm diameter