An oil of S.G of 0.8 is flowingin a stream tube as shown inthe figure. The dischargethrough the tube is 0.06m³/s. The angle at the inlet is0° and at the outlet is 30°.Determinei. the bend force in x-directionii. the bend force in y-directionP2=1.3 barD2=0.2 mFyP1=2 barD1=0.4 mS.G=0.8Q=0.06 m³/s

Answered: Image /qna-images/answer/4686356a-c59d-45fe-8c24-0cfe123f2c29.jpg

Answered: An oil of S.G of 0.8 is flowing in a…

Engineering

Mechanical Engineering

An oil of S.G of 0.8 is flowing in a stream tube as shown in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: For a certain value opening in a shut off valve experiment(exercise 1), the water with a velocity of…

A: given data : u = velocity = 0.65 m/sec dh= diameter of pipe = 24mm= 24*10-3 m. kinematic viscosity…

Q: Brine is flowing through a coil with a velocity of 240 fpm, The pressure foss in overcoming me…

A: Given : Velocity, v = 240 ft/min = 1.2192 m/s Pressure loss, p = 3.134 psia = 21608.169 Outer…

Q: The flow regime pattern for an oil reservoir as the fluid moves from bottomhole to the surface is…

A: The following is the most likely flow regime pattern for an oil reservoir as the fluid moves from…

Q: E thrust of a shaft is taken by a collar bearing provided with a forced cation system. The…

Q: e flow rate

A: Answer=2.2805kg/s

Q: Q3:- A liquid whose coefficient of viscosity is µ flows below the critical velocity for laminar flow…

A: The loss of pressure in a length of 120 m is 11520 N/m2.

Q: Q2/ Water have a surface tension of 0.4 N/m. In a 3 mm diameter vertical tube if the liquid rises 6…

Q: used of measuring the fluid temperature

A: Given; The fluid velocity is doubled the thermal time constant of a thermometer used…

Q: 4 in

A: given:

Q: In fluid flow, it is assumed that the fluid is ideal. a. true b. false c. cannot be defined

A: In fluid flow, it is assumed that the fluid is ideal. Answer: a. true

Q: 2- Velocity distribution of fluid over a flat plate is given by: U = % y - y in which (u) velocity…

Q: * For measuring flow by aventurimeter, if should be installed :in Inclined line. O Vertical line. O…

A: Option (e) : In any direction and in any location

Q: The differential pressure is 15"WC and the distance between the bubbler tubes is 3". Calculate the…

A: Given data: differential pressure, ΔP = 15" WC distance between the bubbler tubes, L = 3" = 3×0.0254…

Q: Container is placed 55 cm from the ground contains fluid with density of 757 kg/m3 and dynamic…

Q: as shown in figure shown below if the velocity of water at point (A)is(30m/s)with pressure of (90000…

A: We have to find pressure and speed of water at point a, b and c

Q: i need the answer quickly

Q: A petroleum crude oil having a kinematics viscosity 0.0001 m²/s is flowing through the piping…

A: Dear student, we are suppose to solve only 3 subparts. Please post other parts as a separate…

Q: A liquid of (u = 1.25 Pa.s.) fills the space of (Sum) shown in figure below. Calculate the forque…

Q: The head loss due to friction over sections in a pipe for an ideal fluid is in Bernoulli's equation…

A: the head loss due to friction over the section in a pipe for an ideal fluid is Zero in Bernoulli's…

Q: Q-3, B.: A Pitot static probe is mounted in a 25 em inner diameter pipe at a location where the…

A: Step 1: To calculate the volume flow rate through the pipe using the Pitot static probe…

Q: In compressible fluids, which is not assumed to simplify calculation a. Steady flow b.…

A: Compressible fluids are the ones which can be compressed whose volume decreases and density…

Q: Spherical particles of density 2000 kg/m3 and in the size range 20– 100 mm are fed continuously into…

Q: Calculate the volume (m3) of the tank needed, using the Van der Waals Equation for - 5kg air at…

A: Given:m= 5 KgT=150 KP=2750 KPa

Q: The picture below depicts a system for delivering chocolate ganache in liquid form. The nozzle on…

A: given : inner diameter of hose =25mm specfic gravity of chocolate=1.1 dynamic viscocity of…

Q: The Reynolds number is defined for a pipe as (velocity· diameter· density) / viscosity. What is the…

Q: In a stationary fluid, The pressure head at same depth inside the fluid with decrease in density of…

A: Option b is correct.

Q: The losses per unit length pipe^h/l in turbulent flow through small pipe depend upon Velocity,…

A: Introduction: Head loss is the energy wasted in a fluid system due to friction along the length of a…

Q: In order to measure the speed of the ambient air at atmospheric pressure, a Pitot tube is used, in…

A: Given data: Ambient air speed (v) = 25m/s air temperature (T) = 40 °C To find: differential…

Q: elocity at a point inside

A: given:x=20cm

Q: (a) State the cquation of contmity for a compressible tluid flowng thouglh a pipe.

A: Continuity equation: It states that" the rate mass of mass entering at any cross-section of a pipe…

Q: De thrust of a shaft is taken by a collar bearing provided with a forced ication system. The…

Q: y aer. A Pitot tube is used to measure the air flow rate in a circular duct 8.5 m I.D. The "riowing…

Q: THE WATER PRESSURE IN A PIPE IS CONSTANT AT 2 BAR .THERE ARE THREE NOZZLES WHICH DIFFER IN THE SIZE…

A: The water pressure in the pipe is constant at 2 bar.When the water exits the nozzles, it does so…

Q: surface tension of fluid If X = Density of fluid x acceleration x diameter of tube , then the unit…

Q: An Unknown Liquid (SG. 0.6651) is flowing through a 59m long copper tube with a radius of 2.5mm at a…

A: Given:Specific gravity of the liquid, S=0.6651Length of the copper tube, l=59 mRadius of teh copper…

Q: Find the volume flow rate and direction of a certain fluid flowing in a tube system as shown below.…

Q: The flow of viscous incompressible fluid around a sphere with very small Reynolds number can be…

Q: Fluid is moving at rate of 3m/s in a chamber of a 12inch positive displacement flow meter, if the…

Question

An oil of S.G of 0.8 is flowing
in a stream tube as shown in
the figure. The discharge
through the tube is 0.06
m³/s. The angle at the inlet is
0° and at the outlet is 30°.
Determine
i. the bend force in x-
direction
ii. the bend force in y-
direction
P2=1.3 bar
D2=0.2 m
Fy
P1=2 bar
D1=0.4 m
S.G=0.8
Q=0.06 m³/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

plz solve question 3 with explanation it within 30-40 mins I'll give you multiple upvote
Q,, A liquid of (N =1.25 Pars.) fills the space of (Sum) shown in figure below. Calculate the forque (T) required to rotate the frustum cone at constant Speed of a (60 rip.u). o. 3m c.7m
Consider the fluid between two parallel plates, in which we move both plates. Which of the ff. is true? A. The velocity distribution of the fluid is parabolic. B. The higher the viscosity of the fluid, the higher the dissipation of momentum across the fluid. C. the higher the velocities of the two plates, the higher the dissipation of momentum across the fluid. D. The higher the difference in velocities of the two plates, the higher the dissipation of momentum across the fluid. E. None of these.
The velocity of a liquid (s.g.=1.96) in a 13-in pipeline is 1.2 ft/s. Calculate the flow in slug/s.
A block is slid down a 16 inclined plane on a thin film of W Imm thickness oil. The contact area between the block and the oil film is 0.0035m. Find the ratio of terminal velocity (m/s) to the block weight (N). h, oil film thickness 0-16°
The shear stresses in the fluid flow are caused by Pressure Temperature Friction Volume
Define : 1- Compressible fluid flow
1.The mass rate of a flowing fluid per unit of cross-sectional area perpendicular to the direction of flow is called: i. average velocity ii. mass velocity iii.momentum flux iv.velocity head 2.An ideal flow is i.with constant velocity gradient in the fluid ii.involves a Newtonian fluid iii.with no friction between fluid layers iv.whose fluid has a viscosity that varies linearly with temp
An incompressible viscous fluid is placed between two large parallel plates as shown in Fig. 1 . The bottom plate is fixed and the upper plate moves with a constant velocity, U. For these condi- tions the velocity distribution between the plates is linear and can be expressed as
If the mass velocity for water at 80°F flowing through a 1 in. diameter tube is 30,000 slug/hr-ft?. What is the Reynolds number? Take a viscosity value of 0.0648 slug/ft-hr.
Briefly describe the different between incompressible and compressible fluid flow.
Derive an exspression for ó the height