pipes in parallel, the total friction head loss equals to the individual friction head loss in each pipe. True or false

Q: QUESTION 1 Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out…

A:

Q: Oil is flowing through the venture meter shown in the figure. The water velocity in the main pipe of…

A:

Q: The ratio of theortical discharge to actual discharge through an orifice is coefficient of discharge…

A: Let us discussion coefficient of discharge.

Q: A horizontal 154 mm diameter pipe gradually reduces its section to 53 diameter, subsequently…

A: Pipe diameter at the inlet, d1=154 mm=0.154 mPipe diameter at the section 2, d2=53 mm =0.053…

Q: The pump in figure 3 delivers water from the reservoir to the nozzle at the rate of 0.13 m/s. The…

A:

Q: An incompressible and viscous fluid flows inside a pipe of length L with relative roughness. It…

A: The friction factor is a measurement of how much pressure a fluid loses in a pipe as a result of…

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: Since you have asked multiple subparts, only the first three subparts are solved for you. If you…

Q: The air is measured at 30 deg. C and 518mm Hg. The duct diameter is 585 mm while the discharge…

A:

Q: 3. Find the rate of flow of water, in 1/s, through a 220 mm-diameter pipe which has a venturi meter…

A: Given: D1 = 220 mm = 0.2m D2 = 140 mm=0.14 m Cd=0.97 h=900 mm =0.9 m

Q: 02: As shown in figure (2), when the pump develops (7.5m) of head, and the velocity of flow through…

A:

Q: ong Stag 2. The following data relate to an inclined venturimeter: Diameter of the pipe line = 400…

A:

Q: In Figure below, the pipe entrance is sharp-edged having K1 = 0.5, and for the open globe valve…

A: Given that, K1=0.5K2=6Flow rate of water, Q=0.015 m3/sec,Density of water, ρ=1000 kg/m3Friction…

Q: D;= 150 mm Water D,- 50 mm Figure 358 Prosiems 3.51, 3.52. 3.51 In Fig 3.58 the losses up to section…

A: Given: The level of water in tank, H = 8 m The diameter of nozzle at A, D = 150 mm The diameter of…

Q: A storage tank has hot water. This water at a temperature of 85 °C is pumped to a 600 cm height at a…

A:

Q: 3. In the following system, the flow rate of Q= 400 lt / s is transmitted from the A chamber to the…

A:

Q: For oil flow through a pipe, velocity increases O 1, with decrease in area of cross section O 2.…

A: Option : With decrease in area of cross section

Q: Sketch a section of a pipe with diameter D₁ with a Venturi meter of throat diameter D2. Indicate on…

A: let pipe diameter=D1throat diameter=D2water column level at pipe =h1water column level at throat=h2

Q: * A hydraulic lift raises a total load of 8 tonnes through a height of 12 m- once in every two…

A: given; total load(m)=8 tonnes                        =8000kgfor every 2 minute.total load rate…

Q: The head loss due to friction is not proportional to length of the pipe.  Select one: True False

A: The head loss due to friction in a horizontal or vertical or laminar or turbulent flow is given by…

Q: Water flows through a reducer in a pipe as shown. The pressure at A is equal to 345 kPa and the…

A: GIVEN DATA - PA=345KPa    dA=150mm PB=325KPa    dB=60mm WE HAVE TO CALCULATE FLOW RATE

Q: An oil of sp. gr. 0.9 is flowing through a venturimeter having inlet diameter 20 cm and throat…

A: We are authorized to answer one question at a time since you have not mentioned which part you are…

Q: Consider a series of pipes as shown in the figure below that carries a discharge of 100 of water.…

A:

Q: Part B Taking in your consideration the head losses accumulated by the fluid when flowing in the…

A:

Q: A fluid flows at 650 (ft^3)/min through the space between two concentric pipes. The inner pipe has…

A: Given: Q = 650 ft3 /min d = 1.5 in.  D = 4 in.    To find: Average velocity, uavg = ?

Q: Water is to be supplied to the inhabitants of a college hostel through a supply main. The following…

A: We have provided data from the question are,  L=4000 m  N=Number of inhabitants=3000  Q=180…

Q: A horizontal 150 mm diameter pipe gradually reduces its section to 55 diameter, subsequently…

A:

Q: 3. Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154 mm) at…

A: Water flows through a schedule-40 pipe that changes gradually in diameter from d1= 6 in (0.154 m) at…

Q: 5. As shown in Figure 4, the water to drive a Pelton wheel is supplied through a pipe from a lake as…

A:

Q: Benzene at 37.8 °C is pumped through the system of Figure at the rate of 0.1515 m³/min. The…

A: Given data Benzene temperature =  37.8 °C pumped at the rate = 0.1515 m³/min.. The gauge pressure…

Q: The piping arrangement shown delivers a jet of water at location C. Water enters the pipe from ne…

A: given minor coefficient bwtween A and B , KAB=7minor coefficient bwtween B and C , KBC=3Diameter of…

Q: Determine minor and major losses.

A: Given: Discharge= 6 l/s TO determine: Major and minor losses

Q: Determine the loss of pressure in overcoming the friction in a coil through which water flows with a…

A: Given information: velocity = 1.2 m/s internal diameter of pipe = 30 mm = 0.03 m Since 10 turns,…

Q: 3. Assume there is friction head loss in the siphon as shown in the Fig. 2.1, where a = 1 m, b = 4…

A:

Q: Draw the right diagram for the problem. Show complete solution. Water at 60 F from a lake through…

A:

Q: Water enters a pipe of diameter 22 mm with a venturi meter with a throat diameter of 12 mm. At the…

A:

Q: 1. A pipe carrying oil of specific gravity of 0.877 changes in size from 150 mm at section 1 and 450…

A: GivenS.G=0.877d1=150mmd2=450mmZ2=3.6mP1=90kPaP2=60kPaQ=150L/s=0.150 m3/s

Q: Two tanks connected by three pipes in series are shown in Figure 2. The lengths of these pipes are…

A:

Q: A pipe of diameter 300 mm and length 3 000 m is used for the transmission of power by water. The…

A: Note: As per policy, we can solve the first one from multiple questions. Please resubmit the…

Q: Question 2 A valve is used to regulate flow in a water pipeline. The pipe has a diameter of 400 mm…

A: Given: Diameter of the pipe→D=400 mm=0.4 m Length of the pipe→L=2500 m (1) Effect of the water…

Q: 3. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a…

A: Given data:- Q = 6 L/s Pressure at the inlet of pump = 2 m of water gage

Q: Water is pumped thru a vertical 50mm new galvanized-iron pipe to an elevated tank on the roof of a…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.