QUESTION 55.1 A pipe of diameter 300 mm and length 3 000 m is used for thetransmission of power by water. The total head at the inlet of the pipe is400 m. Find the maximum power available at the outlet of the pipe. Takef = 0.005.5.2 The head of water at the inlet of a pipe of length 1 500 m and diameter400 mm is 50 m. A nozzle of diameter 80 mm at the outlet, is fitted to thepipe. Find the velocity of water at the outlet of the nozzle if f = 0.01 for thepipe.

Note: As per policy, we can solve the first one from multiple questions. Please resubmit the…

A pipe of diameter 300 mm and length 3 000 m is used for the transmission of power by water. The total head at the inlet of the pipe is 400 m. Find the maximum power available at the outlet of the pipe. Take f = 0.005.

A pipe of diameter 300 mm and length 3 000 m is used for the transmission of power by water. The total head at the inlet of the pipe is 400 m. Find the maximum power available at the outlet of the pipe. Take f = 0.005.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: With reference to the figure below a power station uses a condensor in order to condensate steam for…

Q: 2.60 At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown. At a later…

Q: In this system, d = 6 in., D = 12 in., Az₁ = 6 ft, and A5₂ = 12 ft. The discharge of water in the…

Q: A pipe of diameter 400 mm carries water at a velocity of 20 m/s.The pressure ta point A is 300000…

A: To find : The loss of head between A and B . Given data : The diameter of pipe is (D)=400 mm. The…

Q: A 2-inch copper pipe connection was made from the basement to the second floor in the building. The…

Q: Reynolds number of the flow.

A: Given; Water flows through a pipe having an inner radius;…

Q: A water discharge of 8 m3 s is to flow through this horizontal pipe, which is 1 m in diameter. If…

A: Given Data⇒ Discharge Q=8m3s Horizontal Pipe Diameter of pipe(d)=1 m Assumptions made in…

Q: 1. Water (p = 1000- kg H = 10-3 flows in a horizontal constant-area pipe; the pipe cross ms section…

Q: Reservoir X (Elevation 369m) supplies water to reservoir Y (Elevation 195m) thru a 400 mm pipe. A…

Q: the flow rate in each pipe (+ is out and - is into the reservoir) Assume hA = 60 m, hg = 90 m, hc =…

A: To given…

Q: t the gasoline transfer facility (ρᵣₑₗ=0,75) from the pond of storage to consumption, you want to…

A: The power required to operate a pump between 2 points in the system can be obtained by using the…

Q: Water flows at a rate of 0.0300 m³ /s from reservoir I to reservoir 2 through three pipes connect in…

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: Given:Surface area, Asurf=5.6 m2Inclination angle of door, θ=25oLength of the door, L=1.1 mWidth of…

Q: The discharges from the pipe is 0.142 m3/s of water into a reservoir at a point 1.85 m below the…

A: Given:diameter at point A, da 0.254 mdiameter at discharge, d=30.5 cm or 0.305 mDischarge, Q=0.142…

Q: Elevation = ? reservoir on the right at a rate of 0.45 m/s. The formula for the head losses in the…

Q: Determine the velocity of efflux from the nozzle in the wall of the reservoir of (a) * .Figure, (b)…

Q: The power supplied to the fluid (QγHB/550) by the pump in the Figure is 10 hp. If H = 60 ft and the…

A: Given: The power of the pump is 10 hp. H = 60 ft D = 150 mm

Q: Water from a nearby lake is to be used for a fountain and a water tank. The figure below shows the…

Q: Determine the NPSH available for the system shown. The pump takes water at 30 ° C. The system is…

A: Water temperature, T = 30o C Static head, Hs = 2 m Length of pipe, L = 6 m Pipe diameter, d = 5 cm =…

Q: Answer the attached file

A: The diameter of the pipe between pump and reservoir is D1=20 cm. The length of the pipe pipe between…

Q: The water is flowing through a pipe having diameters 40 cm and 15 cm at sections Tand 2…

A: As per our guidelines, we are supposed to solve only three sub-parts if multiple sub-parts are…

Q: Find discharge A=3 m2 V=2.2 m/s

A: Given that , A=3m2V=2.2m/s

Q: onsider the hydropower schematic shown below with a lake of 70m elevation above a turbine house.…

Q: A reservoir has a depth of 20 ft. A pipe at the base of the reservoir needs to convey discharge of 2…

A: Given data: A reservoir has depth h=20 ft Discharge…

Q: Find the cross sectional area of pipe if discharge through pipe is 333 m3/s and having flow velocity…

A: Given data : Discharge Q=333 m3/s Flow velocity V=50 m/s Required : Cross sectional area

Q: A water discharge 8 m^3/s is to flow through this horizontal pipe, which is 1 m in diameter. If the…

A: Given Data Discharge, Q=8m3/s Pipe diameter, D=1m Velocity, V=QA=8π4(1)2=10.19 m/s

Q: The power transmitted through a pipe is (where Y =Specific weight in N/m3, (Q = Discharge in m3/s,…

A: Power transmitted through a pipe, Power=YQ(H-hf) Y is the specific weight (N/m3) hf is the head…

Q: There is an upward flow from the vertical pipe shown in the figure. If the flow rate is 0.05 m3 / s,…

A: Given data: The flow rate is, Q̇ = 0.05 m3/s. Write the expression to calculate the velocity at…

Q: The water in an aquarium will be drained for cleaning. A flexible tube (D = 4mm) will be used to…

A: The volumetric flowrate of water is 2.587 LPM (litre/min).

Q: 7. A siphon draws oil (sg=0.86) as shown in the figure. Determine the volume flow rate of oil from…

A: Consider 1 is the section in the siphon at the level of oil in the tank, and 2 is the section at…

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: Given:Surface area, Asurf=5.6 m2Inclination angle of door, θ=25oLength of the door, L=1.1 mWidth of…

Q: The three water-filled tanks shown in the figure below are connected by pipes as indicated. If mi…

Q: Find the power (kW) if the area is 2.5 m2 and the head is 5 meters if water is running at 8 m/s.

Q: The flow rate of water through the pipe system shown in the figure is 25 lit/s under the total head…

A: To find :- The total head loss and the diameter of pipeline C. Given:- The flow rate of water is Q =…

Q: Two pipes in a series have a flow rate of 50 L/s. The pipe upstream is 300 mm and reduced downstream…

A: Given Data Q=50 L/s D1=300 mm D2=150 mm

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a hydraulic system, the power is measured as 52 X 10-2 Kilo joules per seconds and pressure is given 320.6 x10-3 N/m2 .Find the flowrate of the hydraulic system.
Reservoir A (Elevation 300m) supplies water to reservoir B (Elevation 180m) thru a 450 mm ductile iron pipe. A turbine is installed in the same level with Reservoir B. The total system flow is 350 gpm determine the the output power in Hp if the turbine is 75% efficient and the total headloss of the system is 3.5m.
A closed tank contain water up to a height of 2 m and over the water surface there is air having a pressure of 90 kPa above atmospheric pressure. Find the discharge through a small sharp-edged orifice of 15 cm dia. at the bottom of tank. Take C=0.6.
Two tanks A and B are connected by a pipe 30 m long. The first 21 m has a diameter of 75 mm and then is suddenly reduced to 50 mm for the next 9 m. The difference of levels between the tank water levels is 2.40 m. Pipe coefficient f=0.005 and the contraction coefficient at sudden change in area is 0.58. Find all the losses, in terms of velocity v2 at exit from the 50 mm2pipe and hence find rate of flow. Draw the Hydraulic gradient line.
Read the question carefully and give me right solution according to the question
oil is being pumped from an open tank A(elev = 110) to another open tank B (elev = 220m) with a total head loss of 15m of oil. The pump has a power rating of 210kW and an efficiency of 65%. Pipe 1 (D=200mm) connects Tank A and the pump while Pipe 2 (D=150mm) connects the pump and tank B. Calculate the velocity of flow in pipe 1, volumetric flowrate of oil, flowrate of pipe 2 and power output of the pump.
A pelton type turbine has installed 37 m below the head gate of the penstock. The head loss due to friction is 26 % of the given elevation. Determine the total head in meters.
A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing process, both pastes are pumped through a pipe, with the red paste lying in the center of the pipe, as shown in Figure Q2. The pipe has an internal radius, R2, and the segment of red paste has a radius R1. The flow is found to follow the Poiseuille equation, i.e. 1 dp u(r) = -- 4µdx (R²2-²) Where u is the viscosity of the paste and dp dx is the pressure gradient. The total flow of toothpaste through the pipe is Qtot, and the flowrate of the red paste is Qred. The toothpaste has a density of p = 1200 kg/m3, and a viscosity of 0.03 Pa.s. The pipe has a radius R2 = 5 cm and a length L = 2 m. a) Find an expression for the flowrate of the red toothpaste. You answer should be in terms of µ, R1, R2, dp dx) b) The flow in the pipe becomes turbulent when the Reynolds number reaches 2000 (where Re is calculated using the mean velocity across the pipe). What is the maximum pressure drop along the pipe…