**Water Flow Measurement and Analysis**Water flows through main pipe A at 300 kg/s, and then out the double wye with average velocities 2 m/s and 3 m/s through pipes B and C, respectively. Use this information to solve problems 18 through 20.![Diagram Explanation]The diagram illustrates a section of piping where water splits from a main pipe (A) into three smaller pipes (B, C, and D). It includes dimensional annotations and flow directions:- Main pipe A is 350 mm in diameter.- Pipe B is 250 mm in diameter.- Pipe C is 150 mm in diameter.- Pipe D is 250 mm in diameter. **Control Volume (CV)** is indicated by a dashed rectangle encompassing the area where the main pipe splits into the three smaller pipes.**Question 18:**The water velocity through pipe A is __________ m/s**Question 19:**The water velocity in pipe D is nearest:(a) 0.78 m/s(b) 31.8 m/s(c) 1.49 m/s(d) 3.03 m/s(e) 2.39 m/s**Question 20:**( T / F ) Using the control volume (CV in figure above) approach, the pressure forces inside pipes B, C, and D would be denoted with arrows perpendicular to and pointing away from the boundaries at the pipes.For educational purposes, ensure you are familiar with the principles of fluid dynamics such as mass flow rate, continuity equation, and control volume analysis to accurately solve these types of problems.

Answered: Image /qna-images/answer/b7ce5c4f-0569-409b-8580-3ad61ea6ef7c.jpg

Answered: Water flows through main pipe A at 300…

Water flows through main pipe A at 300 kg/s, and then out the double wye with average velocities 2 r through pipes B and C, respectively. Use this information to solve problems 18 through 20. 250 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Friday, 9 April 2021 $: Scm 2: 5m Pump Ø = 5 cm 7:2m In SG = 0.8 S9 - 13.5 The pump delivers 20kW of pounr to the yell ow fluid when transferring 20L/S of iAt upward- Find h if the head loss aong the pipe is う5m、
Li10 a. the friction loss (A P ) in the main .duct (A) 0.6m*/s
An oil having a specific gravity of 0.87 is being pumped from a lower reservoir whose water surface elevation is 150 m througha 200mm diameter suction pipe. It is then discharged through a 200 mm diameter pipe to an elevated reservoir whose water surface elevation is 200m The total head loss during the flow from suction to discharge is 12m of oil. Find the volume flow rate of the oil. Select the correct response(s): O0.12 m2/s 0.24 m/s 0.48 m27s 0.36 m/s
Water is flowing through an orifice meter at a rate of 0.096 m² /sec. The diameter of the pipe is 250 mm. Calculate the pressure drop (in Pa) through the orifice meter if the diameter of the throat is 150 mm. Discharge coefficient of orifice meter is 0.62. Density of water is 1000 kg/m³.
0105 Water at 40 °C is pumped from an open tank through 200 m of 50-mm-diameter smooth horizontal pipe as shown in Figure 1 and discharges into the atmosphere with a velocity of 3 m/s. Minor losses are negligible. (a) If the efficiency of the pump is 70%, how much power is being supplied to the pump? (b) What is the NPSHA at the pump inlet? Neglect losses in the short section of pipe connecting the pump to the tank. Assume standard atmospheric pressure. Note: for smooth pipe, friction factor, f = 0.0152 and at 40 °C. kinematic viscosity Temperature (°C) Water vapor pressure (N/m²) Specific weight (N/m³) (m²/s) 6.58 x 10-7 40 7.376 x 10³ 9.731 x 10³ T 3 m ! PUMP 9.731* Diameter = 50 mm Length 200 m e Figure 1
Water is pumped through a 750ft long inch nominal diameter sch 40 pipe. The difference in height between the outlet and inlet planes is given as 50 ft. Pump efficiency is 80% and the power of the motor is 20 horsepower. Friction losses are given as 50 ft-lbt / lbm. Calculate the flow rate in the pipeline.
Two identical pumps are connected in series and deliver water through an 45cmdiameter, 2.2km long, commercial steel pipe from reservoir A (surface elevation = 50m) to reservoir B(surface elevation = 100m). Consider minor losses of a square-edged inlet, exit, and swing-type checkvalve. Determine the discharge, the total head added by the pumps, and the total power output. The pumpcharacteristics for a single pump is tabulated below. Assume that the kinematic viscosity is 1x10-6 m 2/s and a specific weight of 9.79kN/m 3 . Plot the system and pump characteristic curves on a single plot. Besure to label the axes appropriately (i.e., include units). Be sure to include a legend to demark the systemhead curve and the pump characteristic curve.
Answer is 17.4N horizontally and 17.8N vertically.Please show steps in detail.
A long 0.3 m pipeline laid between two reservoirs carries a flowrate of 0.14 m3/s ofwater. A parallel pipe of the same friction factor is laid beside this one. Calculate the approximatediameter of the second pipe if it is to carry 0.28 m3/s
In a 225 mm pipeline 0.14 m3/s of water are pumped from a reservoir of surface elevation30 over a hill of elevation 50. A pump of what power is required to maintain a pressure of 345kPa on the hilltop if the head lost between reservoir and hilltop is 6 m?
oil is being pumped from an open tank A(elev = 110) to another open tank B (elev = 220m) with a total head loss of 15m of oil. The pump has a power rating of 210kW and an efficiency of 65%. Pipe 1 (D=200mm) connects Tank A and the pump while Pipe 2 (D=150mm) connects the pump and tank B. Calculate the velocity of flow in pipe 1, volumetric flowrate of oil, flowrate of pipe 2 and power output of the pump.
PROBLEM 3 Water, p = 1000 kg/m³ and μ = 0.001 kg/m.s, is pumped between two reservoirs at 5 liter/s through 125 m of 5 cm-diameter pipe and several minor losses, as shown in Fig. The roughness ratio is e/d= 0.001. Compute the pump horsepower required. 2₂= 40m Screwed regular 90° elbow Sharp exit Ģ2 1 2₁ = 7m GI Sharp entrance Half-open gate valve Open globe valve 30 cm bend radius 125m of pipe, d= 5 cm Pump