Determine the value of EIv (in lb ft3 ) at the section below the load P for the beam loaded by two concentrated forces if P = 169lb and Q = 68lb.

Q: At the right is the support detail at B. a) What is the normal stress (in MPa) the boom is subjected…

A:

Q: Fixed/built-in or encastré beams are usually used in structure due to their high stability and…

A: FBD, a Free body diagram of a body or a section shows all the forces or reactions acting upon the…

Q: To calculate the components, magnitude, and direction of the resultant force of three coplanar…

A: Answer let us first resolve the forces into their components as shown in figure below Calculation…

Q: Question: A rectangular column shown in the figure has fc'=28Mpa and fy=415Mpa. Assuming e=120mm,…

A: Answer We are given  f'c = 28 Mpa fy = 415 Mpa e =120 mm b = 400 mm h = 300 mm As = 8-25 mmϕ…

Q: For the beam shown, write the shearing and bending moment functions for each segments of the beam.…

A: To simplify the analysis, divide the loads into udl and triangular loads as shown below Now for…

Q: Calculate the reaction forces at each support for the truss shown. Neglect the weight of the truss.…

A:

Q: Consider the beam in (Figure 1). If L = 9m, the beam will fail when the maximum shear force is Vmax…

A: Given Span 9 mConcentrated moments Maximum shear force 5 kNMaximum bending moment 5 kNmTo find out…

Q: Replace the force system acting on the post by a resultant force(Figure 11. Figure 1 m 500 N 0.5 m…

A:

Q: ANSWER THE FOLLOWING PROBLEM QUESTION "Loaded beam". SHOW YOUR SOLUTION AND BOX THE FINAL ANSWER…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: The beam is subjected to a shear force of 180 kN (Figure 1) Part A Determine the shear stress…

A: Given: The shear force in the beam is 180 kN. Consider the figure.

Q: O A long excavation with vertical sides and depth-to-width ratio of 0.5 is to be made in a deep…

A:

Q: Show complete solution. Put your final answers in a box and should be on the third place value after…

A:

Q: Wo B A L

A:

Q: Take that a = 38 mm. (Figure 1) Part A Determine the moment of inertia of the beam's cross-sectional…

A: for flange section     b1=6a   and depth   d1=afor web section  width   b2=a  and  depth…

Q: Part 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the…

A: Part 1 ∑MA=03.5×12×2+122 - Cy×12=0Cy=28 kips∑Fy=0Ay+Cy=3.5×12Ay+28=3.5×12Ay=14 kipsAy=14 kipsCy=28…

Q: Given the beam loaded below, compute the following: a. Reaction @ support A b. Reaction @ support B…

A: Given:- To find:- Reaction at support A Reaction at support B

Q: (Figure 1), a = 45 mm. re 50 mm 150 mm 150 mm 300 mm 1 of 1 Part A Locate the centroid y of the…

A:

Q: Chapter 5, Section 5.2, Question 40 A 50-kN force acts at point D in the yz plane on the linkage.…

A: For calculating we have to find values of following Distance between B and D Component of forces on…

Q: Find the magnitude of the resultant of the concurrent forces if 0 = 24.19°,B = 35.43°, F = 134.4, Q…

A:

Q: Each of the blocks shown in figure (9.14) has mass 1 kg. The rear block moves with a speed of 2 m/s…

A:

Q: Instructions: Follow Given-Required-Solution format for your computation. Complete FBD for full…

A:

Q: A concrete dam is triangular in cross section and 30 m high from the horizontal base. If water…

A:

Q: The member is supported by a pin at A and a cable BC. If the load at D is 300 lb, determine the x,…

A: Given:-  The member is supported by a pin at A and a cable BC. If the load at D is 300 lb,

Q: A trailer truck crossing a 10-m span circular beam (D = 400 mm) has axle loads of 7 KN, 9 KN, and 16…

A:

Q: H.W For the shown beam-column, derive and solve the differential equation of the deflection curve.…

A:

Q: Determine the centroid and the moment of inertia with respect to the x and y axis from the given…

A:

Q: Question- A 100 m tape weighing 30N is suspended between the two ends under a standard pull of 100…

A: Given- L=100 m tape, Weight of tape W=30 N, Standard pull P=100 N, Correct distance between the tape…

Q: Wo В A L

A:

Q: D 600 N 4 m 900 N E 4 m B. Af 6 m

A:

Q: Two concentric heavy steel springs support a load of 9100 N as shown in the figure. The outer spring…

A:

Q: Determine the horizontal component and vertical component of the force that acts at the tip of the…

A: To determine the horizontal and vertical components of the force F acting at the tip of the boom.…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Given :-  Dimension of the suitcase given are = 625×500 mm Forces applied are :-  F1 = 212 N  P =…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.