UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Strength of Materials A trailer truck crossing a 10-m span circular beam (D = 400 mm ) has axle loads of 7 KN, 9 KN, and 16 KNseparated respectively by distances of 2 m and 5 m. Calculate the maximum bending stress and transverse stressdeveloped in the beam.7 kN9 kN-2m-k5m16 KNk10 mR₂

Answered: Image /qna-images/answer/cacdb5e8-93d2-48f6-9c75-80da65f0de9c.jpg

A trailer truck crossing a 10-m span circular beam (D = 400 mm) has axle loads of 7 KN, 9 KN, and 16 k separated respectively by distances of 2 m and 5 m. Calculate the maximum bending stress and transverse stress developed in the beam. 7 kN 9 kN 2m 5m 16 kN

A trailer truck crossing a 10-m span circular beam (D = 400 mm) has axle loads of 7 KN, 9 KN, and 16 k separated respectively by distances of 2 m and 5 m. Calculate the maximum bending stress and transverse stress developed in the beam. 7 kN 9 kN 2m 5m 16 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: compression member about its z axis, and select the correct answer from the list of the provided…

A: Given data: Strength class of timber, C24 fc,o,k=21 Nmm2, E0.05=7400 Nmm2 λz-z=83.16

Q: A closed cylindrical vessel, axis vertical 4m high and Im in diameter is just filled with water. At…

Q: A Structural Number SN, =5.0 and was obtained using a subgrade M, =5000 psi using the AASHTO 1993…

A: given data ,using AASTHO 1993 design method Structure no is SN1,SN2,SN3 for surface ,base, and…

Q: Determine the reactions and draw the shear and moment diagram. Use SLOPE-DEFLECTION METHOD ONLY. 20…

A: Given a fixed beam and it is require to determine the reactions and to draw SFD, BMD by using…

Q: compressive stress is 1000 psi and L = 8 ft, find the minimum dimensions of a neutral axis of the…

Q: A transit with stadia interval factor of 100.8 was set up at point C on the line between points A…

A: Given data : C = 0.38 K = 100.8 a) Horizontal distance between A and B, Horizontal distance…

Q: A square tied column measuring 600mm x 600mm is reinforced with 16-32mm diameter longitudinal bars.…

Q: Using force method find moment at C take Mc as a redundant 120 kN B 6 m 6 m

Q: Determine the support reactions and draw the Shear and Moment Diagram. 500 N A RA 5m C 8 m 800 N-m…

A: Given,

Q: Results of a laboratory consolidation test on a 10 meter thick clay indicates t 50 = 12.5 minutes…

A: given data:- thickness of lab sample=3.18 cm time taken by sample to get 50% consolidation=12.5…

Q: • Part A Replace the loading system acting on the beam by an equivalent resultant force and couple…

Q: Consider the given figure. The bar AC is 6 mm thick and is made of a steel with a 425 MPa ultimate…

A: Given:- The thickness of the bar AC (t) = 6 mm The ultimate stress of the steel = 425 MPa The…

Q: The rigid beam is supported by a pin at B and wires AD and CE. (Figure 1) The load P on the beam…

A: Objective: To determine the normal strain in wires AD and CE. Given: Displacement of end A of the…

Q: The materials shown in the figure are rigidly attached with each othe r. This composite material is…

A: Given, Load, P = 60 kN Temperature difference, ∆T = 50oC

Q: Situation. A floor plan of a proposed five storey concrete building is shown. It carries the…

Q: A surveyor set his instrument up at point A to observe points B and C which are both ahead of his…

A: Given data- The given situation is shown below- Where, i= 2.703 mmd=10 cm = 100 mmf = 27 cm = 270…

Q: Could you please help determine elastic center C Where the square has a modulus of elasticity =…

A: Determine elastic center CWhere the square has a modulus of elasticity = E_w and the two riangle…

Q: Part A: Draw the Free Body Diagram of the system with the distributed load. Part B: Find the…

Q: A rectangular beam has b-300mm, d-500mm. and reinforced at tension side only with 4-28mm bars,…

Q: . Assume that axial eformation of Member EF is aused mainly by its reaction external forces on the…

Q: 1 The 600 KN load is horizontal when it is first applied to the columns. After some time, the 600 KN…

Q: 1. Assume that axial deformation of Member DF is caused mainly by its reaction to external forces on…

Q: A uniform bar is acted upon by different forces as shown. R = 21.75 Ibx 3 ft 1.5 ft 4.5 ft • A • B…

Q: Differentiate between Force (Flexibility) & Displacement ( stiffness)methods of analysis.

A: - Force method of analysis : 1- Force method is also know as Flexibility method, Compatibility…

Q: Using the Force Method of Analysis, determine the support reactions of the beam shown. El is…

Q: Three cables are connected at A, where the forces P and Q are applied as shown. Knowing that Q = 10…

A: Given: Required: Value of P

Q: A timber beam 100 mm wide by 300 mm deep is made by gluing three 100 mm x 100 mm member together.…

Q: A reinforced concrete spiral column having a diameter of 500 mm carries an ultimate load of 5000 kN.…

Q: Two concentric heavy steel springs support a load of 9100 N as shown in the figure. The outer spring…

Q: ose 1 type OI statically determinate 2. Divide the chosen beam into 3 spans, pan is your own choice.…

Q: SKETCH THE FIGURE AND SHOW THE COMPLETE SOLUTIONS

A: Step: 1 Latitude and departure are the projection of a line in north-south and east-west direction…

Concept explainers

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.

Question

100%

UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer.

Strength of Materials

A trailer truck crossing a 10-m span circular beam (D = 400 mm ) has axle loads of 7 KN, 9 KN, and 16 KN
separated respectively by distances of 2 m and 5 m. Calculate the maximum bending stress and transverse stress
developed in the beam.
7 kN
9 kN
-2m-k
5m
16 KN
k
10 m
R₂

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis and procedures for material selection

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) What is the actual shearing stress of the beam in MPa? (use two decimal places, no need for unit)
A trailer truck crossing a 10-m span circular beam ( D = 400 mm ) has axle loads of 7 kN, 9 kN, and 16 kN separated respectively by distances of 2 m and 5 m. Calculate the maximum bending stress and transverse stress developed in the beam.( detailed solution with FBD please, thank you) τmax = ? MPa σfmax = ? MPa
A simply supported beam L meters long carries a uniformly distributed load of 6.8 KN/m over its entire length and has the cross section shown . If the L used will cause a maximum flexural stress of 35 MPa, what maximum shearing stress in MPa is then developed?
1. A steel circular bar (the yield stress oy = 350 MPa) with diameter d = 60mm is acted upon by combined moments M and axial compressive loads P at its ends. Taking P = 500 kN, determine, based on the Von Mises criterion of yield failure, the largest allowable value of M. d M M P- P.
Problem 4: A T section of a beam is fabricated from 2 - 12 mm x 150 mm steel plates and joined by welding as shown in Figure ST-904. It carries a live load of 6.5 kN/m extending half of its span. Neglect the weight of the beam. T 12 x 150 mm 4 m 6.5 kN/m 4 m Compute the maximum compressive stress. ( bending stress in compression) Compute the maximum tensile stress. ( bending stress in tension) Compute the maximum shear stress. Compute the shear stress between the junction of web and flange. Compute the maximum deflection. El is constant.
2. A beam with an inverted U section is loaded as shown. What is the max flexural stress developed and the max beam shear developed in the beam? 30mm 30mm 2m 6m 2m 200m 250mm 40mm
A beam having a span of 4m is subjected to a maximum shear of 20 kN. It has a triangular cross - section having a base width of 140 mm and an altitude of 300 mm. Which of the following gives the maximum shearing stress developed on the beam? a. 1.43 MPa b. 1.80 MPa c. 1.62 MPa d. 1.78 MPa
Strength of Materials Please solve ???
Strength of Materials Please solve with complete solution ???
Pls show complete solution and fbd
Higdon
3. A beam simply supported on a 12-m span carries a uniformly distributed load of 30 kN/m over the middle 6 m. Using an allowable stress of 130 MPa, determine the lightest suitable beam. What is the actual maximum stress in the selected beam? (Shear and moment diagram are optional) 30 kN/m 3 m. 6 m 3 m- Section Modulus (x 103 mm³) 3220 3140 3630 3080 Shapes W610 x 125 W530 138 W610 x 140 W460 x 144 Weight (kg/m) 125.1 138.3 140.1 144.6