Replace the force system acting on the post by a resultant force(Figure 11. Figure 1 m 500 N 0.5 m 0.2 m 300 N 250 N < 1011 Part A Determine the direction of the resultant force Express your answer with the appropriate units. 0-533 Submit Previous Answers Request Answer Part B * Incorrect; Try Again; 7 attempts remaining Determine the magnitude of the resultant force. Express your answer with the appropriate units. FR = Submit N Part C 4 Value 3 P Ć Request Answer K Units ? P Pearson ? Specify where its line of action intersects the post AB measured from point B. Express your answer with the appropriate units. clockwise from the direction to the left ? Copyright © 2022 Pearson Education Inc. All rights reserved. | Terms of Use | Privacy Policy | Permissions Contact Us Review

Replace the force system acting on the post by a resultant force(Figure 11. Figure 1 m 500 N 0.5 m 0.2 m 300 N 250 N < 1011 Part A Determine the direction of the resultant force Express your answer with the appropriate units. 0-533 Submit Previous Answers Request Answer Part B * Incorrect; Try Again; 7 attempts remaining Determine the magnitude of the resultant force. Express your answer with the appropriate units. FR = Submit N Part C 4 Value 3 P Ć Request Answer K Units ? P Pearson ? Specify where its line of action intersects the post AB measured from point B. Express your answer with the appropriate units. clockwise from the direction to the left ? Copyright © 2022 Pearson Education Inc. All rights reserved. | Terms of Use | Privacy Policy | Permissions Contact Us Review

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rod shown below is made of two different materials. Segment AB is made of aluminum (G = 3.9 × 106 psi). Segment BC is bonded to segment AB and is made of brass (G= 5.6 × 106 psi). Segment BC is hollow and has an inner diameter of d₁ = 1.0 in. External torques are applied to the rod at point B and point C. Let L₁ = 53.0 in, LB = 42.0 in, dA dд = 3.0 in, dB = 2.2 in, TB = 9.0 kip in, and Tc = 10.0 kip in . • . B di TB Tc LA LB
Verify whether the system of forces shown can be replaced by a single equivalent force. If it can be replaced determine the point where the line of action of the single equivalent force intersects with the xz-plane. Note: If the system cannot be simplified into a single equivalent force system, write CS (Cannot be Simplified) into the answer box. y A 12 kN 30 kN B 18 kN 300 mm 18 kN 30 kN 500 mm 400 mm D 16 kN
Can you answer this in 30 mins, ASAP Show your complete solution.Input correct unit. Enclose all final answers. Determine the centroid and the moment of inertia with respect to the x and y axis from the given T-beam. Width of the upper flange is 300mm and its height is 75mm, while the web's length is 250mm with a base of 50mm.
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Two forces are applied as shown to the corners B and D of a rectangular plate. Given: P=110-N. M = D 300 mm 50° E P 500 mm 50° N·m (Counterclockwise) C Determine the moment of the couple formed by the two forces by resolving each force into horizontal and vertical components and adding the moments of the two resulting couples. (You must provide an answer before moving to the next part.) B
In (Figure 1), F = {80i + 96j + 48k} lb. Figure 1 ft -2 ft 3 ft 45° B 1 of 1 Part A Determine the magnitude of the moment of F about point A. Express your answer in pound-feet to three significant figures. 15] ΑΣΦ11 MA = Submit Part B α, B, y = Submit Request Answer Provide Feedback Determine the coordinate direction angles of the moment of F about point A. Express your answers in degrees to three significant figures separated by commas. vec U/ ΨΕ ΑΣΦ ↓↑ vec Request Answer ? lb. ft ? Next >
Remaining Time: 52 minutes, 15 seconds. Question Completion Status: SHARED TUTORIAL SES OR GROUPS UST CE E018 AY2223 2.0 = DO NOT INCLUDE NEGATIVE SIGNS IN YOUR ANSWERS Calculate the magnitude and direction of resultant with respect to the x-axis. 1. R = KN use 2 decimal places • use 3 decimal places F3 Calculate the moment of the force system about point A, if L = 2.8 m. 3. M = KN-m use 3 decimal places
Determine the magnitude of moment (Nm) of the 346-N force about point A if x = 0.41 m, y = 0.67 m, and 8 = 35.9⁰. Round off only on the final answer expressed in 3 decimals. Instead of units, type either POSITIVE or NEGATIVE to indicate the direction of moment which is consistent with the sign convention discussed on lectures. Sample answers are 12.908 POSITIVE or 12.908 NEGATIVE. у ...
e.g. 50.00, to have full credit. NEED to include the unit of your answer. se DO NOT COPY the answer of your classmates since the exam that was prepared for you generates 200 sets, so everyone will have d luck and God Bless. Question 3 What is the location of the Maximum moment from A in meters. Given: w1 = 43, w2 = 11, a 4, b = 2, and c = 4. %3! w1 kN/m w2 kN/m D. A B am b m cm Previous 0Y G