Part AThe assembly consists of two 15-kg bars which are pin connectedThe bars are released from rest when 0 = 60°. The 5-kg disk at C hasa radius of 0.5 m and rolls without slipping. (Figure 1)Determine the angular velocity of the bar ABat the instant 0 = 30° , measured clockwiseExpress your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity iscounterclockwise.Ivo AEO| 1t vecWAB = 1.13rad/sFigure1 of 1 >SubmitPrevious Answers Request AnswerX Incorrect; Try Again; One attempt remaining3 m.3 mPart BICDetermine the angular velocity of the bar BC at the instant 0 = 30° , measured counterclockwiseExpress your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angularvelocity is clockwise.

Answered: Image /qna-images/answer/6edfb0dc-d23d-45a2-9132-e32c8857517b.jpg

Part A The assembly consists of two 15-kg bars which are pin connected. The bars are released from rest when 0 = 60°. The 5-kg disk at C has a radius of 0.5 m and rolls without slipping. (Figuro 1) Determine the angular velocity of the bar ABat the instant 0= 30° measured clockwise Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. Va AEo t vec WAn =|1.13 rad/s Figure < 1 of 1 Submit Previous Answers Request Answer X Incorrect; Try Again; One attempt remaining Part B Determine the angular velocity of the bar BC at the instant 0 = 30° , measured counterclockwise Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. vec

Part A The assembly consists of two 15-kg bars which are pin connected. The bars are released from rest when 0 = 60°. The 5-kg disk at C has a radius of 0.5 m and rolls without slipping. (Figuro 1) Determine the angular velocity of the bar ABat the instant 0= 30° measured clockwise Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. Va AEo t vec WAn =|1.13 rad/s Figure < 1 of 1 Submit Previous Answers Request Answer X Incorrect; Try Again; One attempt remaining Part B Determine the angular velocity of the bar BC at the instant 0 = 30° , measured counterclockwise Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. vec

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use the force method to find the value of the redundant force RCx. All bar areas are the same. (Ans: RCx = 15.71 k) A B 30 ft· D 60 k 30 ft [T] E 0x00 20 ft
Answer and solve the following problem.
m = 0.19 kg k= 162 N/m Urgent,please solve quickly about these information.
SN=130
A constant head permeability test is performed on soil that is 4 cm2, and 2.5cm long. The head difference applied during the test is 20 cm and 7 cm3 is collected over a time of 100 sec. Provide step by step solution. What is the permeability based on these test conditions and results.
One end of a uniform wooden beam of length L and weight W is set on a rough floor. A support wire is attached to the beam at a distance of 4L from the other end. The support wire is run horizontally and attached to a post. In this configuration, the beam makes angle e with respect to the vertical. When a ball of weight W is hung at the end of the beam, the bottom of the beam does not slip. Derive an expression for the magnitude T of the tension in the support wire in terms of relevant system parameters. 4L W L W W tan O2W tan 0 Wetne O2Wctne Ө
A 5-kg rod of uniform cross section is used to form the shaft shown. Knowing that the shaft rotates with a constant angular velocity ω of magnitude 12 rad/s, determine (a) the magnitude of angular momentum HG of the shaft about its mass center G, (b) the angle formed by HG and the axis AB.
When the mechanism is released from rest in the position where 0 = 40°, the 6.9-kg carriage drops and the 9.4-kg sphere rises. Determine the velocity v of the sphere when 0 = 180°. Neglect the mass of the links and treat the sphere as a particle. 255 mm 9.4 kg 255 mm 255 mm 6.9 kg Part 1 Using the fixed pivot point as (when 0 = 180°). datum, find the potential energies in postion 1 (when 0 = 40°) and in position 2 Answers: V1 = i NOm V2 = i NOm
I need solution of both the parts
For the truss shown in Figure 2.3a, determine the force in member BH if m= 5 m, n = 4 m, a = 76°, and P = 1.45 kN. Indicate whether the member is in tension or compression. (Note: Use negative sign (-) if the member is in compression.) A J m Hm Gm F m B PKN C n D α E
fast
help