Learning Goal:To calculate the components, magnitude, anddirection of the resultant force of three coplanarforces.Three cables are attached to a bracket as shown in(Figure 1). The tensions in the cables are F₁ = 675N F-900 N, and F₁ = 650 NFigureF₁30⁰1 of 1YCalculate the horizontal component of the resultant force.Course HomeExpress your answer to three significant figures with appropriate units.► View Available Hint(s)FR₂=SubmitPart BHAValueSubmitHÅFRy= ValueCCalculate the vertical component of the resultant force.Express your answer to three significant figures with appropriate units.▸ View Available Hint(s)Units3 → CUnits??Calculate the magnitude of the resultant force.Course HomeExpress your answer to three significant figures with appropriate units.View Available Hint(s)YFR = ValueSubmitPart DHAC0=Calculate the direction of the resultant force. Give the angle between the force and the positive z-axis.Express your answer to three significant figures with appropriate units.▸ View Available Hint(s)SubmitμAValueUnits4Units??

Answer let us first resolve the forces into their components as shown in figure below Calculation…

To calculate the components, magnitude, and direction of the resultant force of three coplanar forces. Three cables are attached to a bracket as shown in (Figure 1). The tensions in the cables are F = 675 N, F₂-900 N. and F3 = 650 N

To calculate the components, magnitude, and direction of the resultant force of three coplanar forces. Three cables are attached to a bracket as shown in (Figure 1). The tensions in the cables are F = 675 N, F₂-900 N. and F3 = 650 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 1154-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 424 mm2. Find the magnitude of P (in N) that can be safely applied to the bar if the stresses in AC and BD are limited to 148 MPa and 86 MPa, respectively. Express your answer in two decimal places.
Determine the magnitude of the pin force at A. Assume W = 845 Ib, a = 3.0 ft, b = 2.0 ft, r = 9 in. a a C В A W D Answer: A = i Ib
3. The rigid bar AB, attached to two vertical rods as shown in Figure 3, is horizontal before the load P is applied. Determine the vertical movement of P if its magnitude is 50 kN. Aluminum L= 3 m A = 500 mm² E = 70 GPa A 3.5 m FIGURE 3 P B Steel L= 4m A = 300 mm² E = 200 GPa 2.5 m C
The figure shows a single acting rivet connecting steel plates. Rivet diameter d = 22 mm,plate thicknesses are t1 = 20 mm, t2 = 12 mm, plate width b = 100 mm and e = 38 mm. The shear strength in the material is τem = 100 MPa, the safety stress in pressure and tension is σL = 280 MPa andSince σem = 140 MPa, determine the maximum force P that the joint can safely carry.
Derive the singularity equation of moment for the beam shown in figure I then:- 1- Draw bending moment diagram for the beam (by using the singularity- Macaulay's equation) 2- Determine the maximum bending stress in the section (square section with side length of 40cm)
Two wires support a weight W. The stresses in the wires AB and AC are not to exceed 81 MPa and 161 MPa, respectively. The cross- sectional area of the two wires are 353 mm? for AB and 139 mm2 for AC. Wire AB is inclined 23-degrees with the horizontal and wire AC is inclined 46-degrees with the horizontal. Give the largest weight W (kN) that can be supported by the wires? Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. B A W
Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while point D is hinged connected. If the rod on the right is heated by 18 degree Celsius, 2 m 2 m 2 m Use E = 200 GPa, linear of coefficient expansion = 11.7 x 10 per degree celsius and A = 4500 mm- Calculate the deformation of the left rod in mm Select the correct response: 00468 mm 0168 mm
Two blocks A and B, each having a mass of 7.5 kg, are connected by the linkage shown. Neglect the weight of the links. (Figure 1) Figure O 30° 30 30° 1 of 1 Part A If the coefficient of static friction at the contacting surfaces is μ = 0.5, determine the largest force P that can be applied to pin C of the linkage without causing the blocks to move. Express your answer to three significant figures and include the appropriate units. P = Submit μÅ Value Provide Feedback Request Answer Units ?
For the beam shown, calculate the bending stress at a point 70 mm. from the top of the beam. P = 59, a = 233, b = 296 Round your answers to 2 decimal places.
Determine the magnitude of the pin force at A. Assume W = 530 Ib, a = 3.6 ft, b = 2.9 ft, r = 9 in. a a B A W D Answer: A = i Ib
L1 = 510 mm L2 = 460 mm L3 = 690 mm
Both wires have a cross sectional area of 17 mm? and are constructed of the same material with a modulus of elasticity of 200,000 MPa. 1. Determine the wires' tensile stress at C. 2. Determine the wires' tensile stress at D. 3. Calculate the maximum displacement possible. 900 mm 450 mm C D 500 mm 1250 mm P=1500 N 1650 mm