Two concentric heavy steel springs support a load of 9100 N as shown in the figure. The outer spring is made from a 30-mm diameter wire on a mean diameter of 220 mm and has 22 turns. The inner spring consists of 30 turns made from 20-mm diameter wire on a mean diameter of 160 mm. Using G = 83 GPA. calculate the shearing stress developed in the two springs 9100 N outer spring inner spring

Two concentric heavy steel springs support a load of 9100 N as shown in the figure. The outer spring is made from a 30-mm diameter wire on a mean diameter of 220 mm and has 22 turns. The inner spring consists of 30 turns made from 20-mm diameter wire on a mean diameter of 160 mm. Using G = 83 GPA. calculate the shearing stress developed in the two springs 9100 N outer spring inner spring

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques…

Q: A cantilever timber beam with a span of L = 2.2 m supports a uniformly distributed load w. The beam…

Q: A bar spring arrangement as shown in the figure is subjected to temperature rise given by Due to…

A: temperature rise given by

Q: A bent rod has a diameter of d=15 mm and is subjected to a force of P= 600 N. What is the normal…

Q: Cords AB, AC, and AD in (Eigure 1) can sustain a maximum tension of 65 N before they fail Figure 1…

Q: Determine the magnitude of the pin force at A. Assume W - 615 lb, a = 3.2 ft, b = 2.3 ft, r = 9 in.…

Q: Determine the minimum cross-sectional area in in? of a steel bar required to support a tensile force…

A: Solution Given Data Tensile Force P= 68 kipsAllowable unit stress σallow= 30 ksi

Q: Determine the minimum diameter d of the rod to safely support the load. The rod is made of a…

A: Calculate the maximum moment of beam and shear force Calculate the moment of inertia of a circle and…

Q: For a given stress tensor the minimum principal stress is 50 20 200 20 40 unit.

Q: 1-Calculate maximum axial stress in the cross section shown below in ksi, if M="see above". Please…

A: Axial Stress : Axial stress is the stress applied along a member or a body. The deformation of…

Q: Given the following principal stress tensor, what is the resulting tensor if we apply a rotation of…

Q: The block of wood glued together as shown is subjected to a compressive force of P=34 kN. Determine…

Concept explainers

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.

Question

100%

UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer.

Strength of Materials

Two concentric heavy steel springs support a load of 9100 N as shown in the figure. The outer
spring is made from a 30-mm diameter wire on a mean diameter of 220 mm and has 22 turns. The inner spring
consists of 30 turns made from 20-mm diameter wire on a mean diameter of 160 mm. Using G = 83 GRA
calculate the shearing stress developed in the two springs
9100 N
outer
spring
inner
spring

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis and procedures for material selection

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

help me asap pls :((
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa
A beam having the cross section shown is subjected to a couple M0 acting in a vertical plane. Determine the largest permissible value of the moment M0 of the couple if the maximum stress is not to exceed 103 MPa. Given: Iy = Iz = b4/36 Iyz = b4/72
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 19 mm and an elastic modulus of E = 69 GPa. The steel rod has a diameter of 22 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.7 m, and c = 1.3 m. What is the magnitude of load P that is necessary to displace point A 9 mm to the left?
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 18 mm and an elastic modulus of E = 77 GPa. The steel rod has a diameter of 24 mm and an elastic modulus of E = 180 GPa. Assume a = 3.5 m, b = 1.8 m, and c = 1.1 m. What is the magnitude of load P that is necessary to displace point A 8 mm to the left?
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
The material used for the shaft has an allowable shear stress of tallow= 40 MPa. If the members are connected together with a fillet weld of radius r= 2.25 mm, determine the maximum torque T that can be applied. Where will the largest stress occur? 30 mm 30 mm 15 mm T T T Figure 6
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
a=2 b=5 80*a=160 90*b=450 100*b=500
A rigid block AB of weight 800 N hangs on an equally spaced vertical wires, two of steel and one aluminum. The wires also support a load P acting at the midpoint of the block. The diameter of the steel wire is 2 mm and that of aluminum wire is 4 mm. what load P can be supported if the allowable stress in the steel wires is 220 MPa and in the aluminum wire is 80 MPa. Use E = 200 GPa for steel and 70 GPa for aluminum. ////// St Al St A W = 800 N
The rigid bar AB is hinged at A and supported by a steel plate hanger. The hanger is fixed at C and bolted at D with two plates. D Given: Width of plate hanger = 40 mm Thickness od plate hanger = 10 mm Bolt diameter = 20 mm 2 m 1.2 m B Allowable bolt shear stress = 60 MPa Allowable bolt bearing stress = 250 MPa W a. What is the allowable stress in the hanger based on bolt capacity in double shear at D. b. If the maximum tensile stress in the hanger is 130MPA, find the allowable load W c. If the load W= 60KN, find the vertical displacement at B.