Determine the normal stress acting at member BC if a vertical force of F = 69 kN is applied at joint B using the figure below. Member AB has a cross-sectional area of 0.002 m2 and member BC has a cross- sectional area of 0.007 m2. The distance between joints A and C is 4.4 m, and the distance between joints A and B is 7.8 m. Answer directly.

Determine the normal stress acting at member BC if a vertical force of F = 69 kN is applied at joint B using the figure below. Member AB has a cross-sectional area of 0.002 m2 and member BC has a cross- sectional area of 0.007 m2. The distance between joints A and C is 4.4 m, and the distance between joints A and B is 7.8 m. Answer directly.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Prob 1. Determine the smallest diameter rod that will safely support the loading shown. The allowable bending stress is oallow = 167 MPa and the allowable shear stress is Tallow = 97 MPa. 25 N/m 15 N/m 15 N/m 1.5 m 1.5 m
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 3450 mm2 and an allowable normal stress of 65 MPa. Bar (2) has a cross-sectional area of A2 = 3300 mm2 and an allowable normal stress of 120 MPa. Assume x1 = 2.1 m, x2 = 3.4 m, y1 = 0.8 m, and y2 = 2.5 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
The cross-sectional dimensions of the beam shown in the figure are a = 4.7 in., b = 6.3 in., d = 4.3 in., and t = 0.34 in. The internal bending moment about the z centroidal axis is M, = -3.60 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. y (Сур.) d a Answers: (a) Omax T = psi (b) Omax C = psi
Four steel bars jointly support a mass of 25 x 10³ kg. Initially the temperature is 25°C. Bars A and D have a cross- sectional area of 480 mm². For bars B and C, the cross-sectional area is 360 mm². Determine the elongation of bar A when the temperature becomes 60°C. Also, find the axial stress developed in bar C. Use E = 200 GPa and a = 11.7 x 106 m/ (m°C). 800 mm 25000 kg 20
Current Attempt in Progress The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 5.3 in., d = 4.5 in., and t = 0.30 in. The internal bending moment about the z centroidal axis is M2 = -4.20 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. | (ур.) d a a Answers: (а) Оmax T psi (b) Omax C = psi
Question 8 20 Points Two plates each 25 mm thick and 130 mm wide are fastened by three 20 mm diameter rivets. Assume that the applied load P = 70 kN is distributed equally among the three rivets. Determine the tensile stress (MPa) in the plate at the critical section. ... P 000- P
The cross-sectional dimensions of the beam shown in the figure are a = 5.0 in., b = 5.9 in., d = 4.0 in., and t = 0.34 in. The internal bending moment about the z centroidal axis is M, = -3.95 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. y (Тур.) d a a
2. If the bending stress at section 2 =20 MPa. What are the bending stresses at sections 1, 3, and 4. 12 mm 12 mm 12 mm NA 276 mm 12 mm 150 mm 123
3. The shaft in the figure below consists of 75 mm diameter bronze segment that is rigidly joint to 50 diameter steel segment. The ends of the shaft are attached to rigid supports (fixed supports). Calculate the absolute maximum shear stress developed in each segment when the torque T = 5.1 kN-m is applied (a = 2 m and b = 1.5 m). Use G = 35 GPa for %3D %3D %3D bronze, and G = 75 GPa for steel. %3D 75 mm 50 mm A Bronze Steel C T a -
Question 2: Two-pinned connected bars supported the rigid member BC as shown. A vertical load of 25 KN is applied to BC at a distance x from bar AB. What should be the distance x to make the stresses in two bars the same? The area of bar AB is 100 mm² and of bar CD is 150 mm². A 8 600 mm P= 25 KN D
Cylinder of height 2H. radius R. centroid at (0,0.H), axis e3 undergoes deformation x = o(z) = z + 23e3. Assuming stress-strain relation: S = aE, where a is a constant, total force on the base of the cylinder with normal -e3 is f = -1.5anR2 He3 total force on the base of the cylinder with normal - ez is f = 1.5aπR²e3 total force on the base of the cylinder with normal - ez is f = 1.5an R²Hez total force on the base of the cylinder with normal - ez is f = -1.5anR²e3
Question 1. The plane NN' makes an angle 8-30" with respect to the cross section of theprismatic bar shown in Figure. The dimensions of the rectangularcross section of the bar are 3cmx6cm. Under the action of an axial tensile load P, the normal stress of NN' plane is o, =60 MPa. a.Determine the value of axial load P b.Determine the shear stress t on the NN' plane c. Determine the maximum shear stress in the bar. P N'