The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Calculate the shear strain, Yxy, at A. Also, calculate the average normal strain & along the x' axis. 45 S 800 mm 45°/ 45 800 mm A' 5 mm

The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Calculate the shear strain, Yxy, at A. Also, calculate the average normal strain & along the x' axis. 45 S 800 mm 45°/ 45 800 mm A' 5 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Situation 41, 42 and 43 20 MPa 80 MPa 80 MPa 20 MPa O Zoom image Determine the normal stress along…

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d= 0.625 in., and each side…

A: - Horizontal axis = 0- Vertical axis = 0- Resultant force on pin is given by PR ;

Q: The rod has a diameter of 40 mm. It is subjected to the force system Fx=1300 N=1300 N, Fy=500 N=500…

A: The diameter of the rod, D = 40mmThe force at the free end, Fx=1300 N, Fy=500 N, Fz=800 N The rod is…

Q: Q1:- At a certain point on the outside of a shaft, which is subjected to a twisting moment (torque)…

Q: Problem 4 The horizontal force of p 85 kN acts at the end of the plate. The plate has a thickness of…

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A: Solution attached below

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given Data: The distances are given as: u=2.8 mmv=5.7 mmc=620 mm The angles are given as: α=30°β=60°…

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

A: For the given bell crank:

Q: The couple M acts in a vertical plane and is applied to a beam oriented as shown. Determine the…

Q: 1. The lap joint in Figure 1 is connected by three-20 mm diameter rivets. Assuming at the axial load…

A: Given data in question Load Diameter To find out Shear stress Bearing stress Maximum average…

Q: a B. u R Answer: prad Y = i

Q: 2-22. The triangular plate is fixed at its base, and its apex A is given a horizontal displacement…

Q: The rectangular bar has a width of w= 2.75 in. and a thickness of t = 2.00 in. The normal stress on…

A: Given : W = 2/75 in. t = 2.00 in Normal stress on plane AB of the rectangular block is 6ksi

Q: The state of plane-stress at a point is given by ox = -200 MPa, oy = 100 MPa and Tyy = 100 MPa. The…

A: Given: σx=-200 MPaσy=100 MPaτxy=100 MPa

Q: The strain components for a point in a body subjected to plane strain are &x= -970 με, &y=290μe and…

Q: Why is the force Fd pointing downwards? By force equilibrium, shouldnt it be 3 + Fd = 9 Fd =…

A: yes, you are right by equalibrium condition 3+Fd=9 we calculate reactions using the equailibrium…

Q: The rod shown in the figure is loaded at points A and B. The circular cross section has a diameter…

A: P = Axial compression forceP = 400 KN V = Shear forceV = 20 KNT = Torque = 20*2T = 40 KN-mM =…

Q: The strain components for a point in a body subjected to plane strain are &x= -1090 μe, &y=-200μe…

A: Given Data: εx=-1090 μεεy=-200 μεγxy=-724 μradIt is asked to calculate:1. Principal strains2.…

Q: Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses…

Q: *2-24. The triangular plate is fixed at its base, and its apex A is given a horizontal displacement…

A: The triangular plate with dimensions as shown in the figure below,Horizontal displacement,…

Q: The rectangular bar carries a load of P = 127 kN and is connected to the support bracket with a…

A: As said, the pin experiences double shear, Shear stress is given by ;Since, double shear so,…

Q: 4Kips 10 KIPS 0.5 in.diam. 1in diam. lokips 8kips 0.75 in diam.

A: for First segment Dia = 0.5 in. Load = 4kips for Second segment Dia = 1in. Load = 14 kips…

Q: A solid circular bar is fixed at point A. Thebar is subjected to transverse load V = 70 lb andtorque…

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

Q: The same torque is applied to two tubes with identical metal sheets, determine the ratio of…

Q: En O E2 9 Rosette shown E₁ What would be a shear strain in at the given point ? If €₁=25μ E₁ = 40μ…

Q: The couple M = 78 kip-in. is app section shown in a plane formin vertical. Determine the stress at…

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

Q: Draw Mohr's circle and find: 1) Principle stresses and their direction. 2) Maximum Shear stress and…

Q: The 60° strain rosette is attached to point A on the surface of the support. Due to the loading the…

Q: The solid 1.25-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: In the virtual work equation for trusses, S is the axial stress in a member due to the actual…

Q: Four steel bars jointly support a mass of 25 x 103 kg. Initially the temperature is 250C. Bars A and…

Q: Four steel bars jointly support a mass of 25 x 10³ kg. Initially the temperature is 25°C. Bars A and…

A: Given, M = 25000 kg T1 = 25oC AA = AD = 480 mm2 AB = AC = 360 mm2 E = 200 GPa α = 11.7 x 10-6 /C

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Determine the shear strain y at corner Q' after deformation.

Q: SITUATION. A square post is made up of two parts glued at an angle of 30 from the vertical axis.…

Q: For the given plane stress state Ob=120 MPa, te= 100 MPa and oa=150 MPa , a) Calculate the stresses…

A: Consider the figure shown below.

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

Q: 2-23. The triangular plate is fixed at its base, and its apex A is given a horizontal displacement…

A: The triangular plate with dimensions as shown in the figure below,Horizontal displacement,…

Q: Current Attempt in Progress A thin triangular plate PQR forms a right angle at point Q. During…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to…

A: Given data, u = 2.4 mm v = 5.8 mm c = 730 mm α = 25° β = 65° To find out the shear strain γ at…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

The triangular plate is fixed at its base, and its apex A is
given a horizontal displacement of 5 mm. Calculate the
shear strain, Yxy, at A. Also, calculate the average normal
strain Ex along the x' axis.
45°
800 mm
45°
45°
800 mm
A'
5 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:

VIEW

Step 2: Calculation of shear strain:

VIEW

Step 3: Calculation of average normal strain:

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the element in with Txy = 30 MPa. 80 MPa Part A 01, 02 Determine the principal stresses. Enter your answers in megapascals to three significant figures separated by a comma. = T vec Submit VE ΑΣΦ | 41 Txy Request Answer
From the previous problem, determine the shear stress 30 mmabove the neutral axis.
If Øxx = 110 MPa, Oyy = - 86 MPa, ozz = 55 MPa. Txy = 60 MPa, and allþther components are zero. Determine the principal stresses and the direction cosines of the principal axis. Also find the octahedral normal and shear stress components. Q.4:
2
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.3 mm and upward by v = 5.2 mm to new position Q'. Determine the shear strain y at corner Q'after deformation. Use c= 665 mm, a = 23°, and B = 67°. P R Answer: Y = i prad
The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load P as shown. a. Determine the torsional shear stress at Point A (50mm from the center) and Point B (on the Surface) b. Determine the absolute maximum torsional shear stress in the shaft. c. sketch the state of stress at point A and draw its corresponding Mohr’s Circle of stress. compute the principal stresses and maximum in-plane stress. T=10.38kN-m
A 60° strain rosette is glued to a girder. At any instant the measured strain values are: - 220u ; - .360µ; e - 500;µ Apply the concept of Strain Transformation to determine: (i) The coordinate strains , &, and y,; if e=10 (ii) Using transformation equations; (a) The orientation of principal planes and the values of max. and min. principal strains. Also sketch the deformed strain element showing principal planes labelled with max. and min. principal strain values on the respective planes. (b) The orientation of max. in-plane shear strains and the values of max. and min. in plane shear strains. Also sketch the deformed and distorted strain element labeled with strain values on the respective planes.
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.1 ksi, If t 1.9 in. and b= 3.8 in., 3 in. a. determine the largest P, which is vertical, the frame can 3 in. carry 30 b. determine the largest P, which is normal to AC, the frame can carry
2. The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.12 in. Use 2 decimal places. (25 pts) steel L = 4 ft A = 0.5 in? E = 29 × 10° psi P =? A B C 3 ft 2 ft
What is the normal stress on the oblique plane due to the load P? 155 kip 7 in P = a = b = 4 in a = 37 degrees
The rectangular plate undergoes a deformation shown by the dashed lines. Determine the shear strain gxy and gx′y′ at point A.