Determine the moment about point P. Express as a Cartesian vector. 3 44 -G 10-2 Fea 2 m 2 m 3 m F= [3 i +4j-6 k] kN

Q: How much force in lbs will it take to lift a 10 -lb weight with a wheel and axle, when the axle is…

A:

Q: A torque of 18 N m is applied to a rotating part. The part has a moment of inertia of 0.078 kgm2.…

A: Here we will use the the torque equation and the rotational motion equation.

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: In the figure shown, gear A rotates at 300 rpm. Gear S is fixed and has 80 teeth. The three…

A: Write the given data. Speed of arm, Narm=180 rpmSpeed of anulus gear, NA=300 rpmSpeed of gear S,…

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: The first gear in a single - stage gear train has 42 teeth and an angular velocity of 2 revolutions…

A: Given,The first gear in a single - stage gear train has 42 teeth and an angular velocity of 2…

Q: Question Figure Q1 shows the schematic diagram of a moulding press, which is driven by a crank BC…

A: Figure Q1, shows the schematic diagram of a moulding press, which is driven by a crank BC rotating…

Q: A compound gear train with gears P,Q,R and S has number of teeth 30, 50, 20 and 30 respectively.…

A: Given that: Number of teeth in gear P, Q, R and S are 30, 50, 20 and 30 respectively. Gear Q and R…

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: If a spur gear has a pitch of 18 teeth per inch and 29 countable teeth, what is the diameter of that…

A: Pitch, P= 18 teeth per inch Number of teeth, T= 29   To find: Diameter of the gear in inches, D

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: Part A - Construction of Mohr's circle for the state of stress For the element shown, construct…

A: Given Data

Q: I want to buy a two METAL SPUR GEAR for my 2 pieces of G.I pipe with an 3 inches diameter (3mm…

A:

Q: Gear 2 in the diagram below is driven at a speed of 126 revolutions per minute. Gear 2 has 16 teeth,…

A: The gear train is simple,The speed ratio of a simple gear train with 2 gears is as follows,Here,N is…

Q: For practical working gears as manufactured, typically the addendum, a, is larger than the dedendum,…

A: Addendum: The distance between the top land and the pitch circle on a gear tooth, is called as…

Q: f e (D d b C a k j a=38.0 b=41.5 c=39.3 d=40.1 e=55.8 f=39.4 q=36.7

A: a = 38.0b = 41.5c = 39.3d = 40.1e = 55.8f = 39.4g = 36.7h = 65.7i = 49.0j = 50.0k = 61.9l = 7.8m =…