stressDetermine the Maximum Normal S deviloped in the bar bth at the crom sectionContaining the hole and at the cross sechion Gntaiming the fillets when it's subjectedto a tension of P.tamWom Owhile:P- 30 KNW= 52 mmt- 4 mmhe 24 mmww 7Fde 22 mmk: 90 mmS: Li4 mm

Stress concentration for the fillet - wh = 5224 = 2.167andrh = 1424 = .5833Hence,K = 1.5 Maximum…

Determine the Maximum Normal ste developed stress in the bar buth at the cim section Containing the hole and at the cross sechon Gntaning the fillets when it's subjected to a tension of. tam while: P- 30 kN P. W= 52 mm t- 4 mm he 24 mm 14 mm de 22 mm k: 90 mm %3D S: Lile mm

Determine the Maximum Normal ste developed stress in the bar buth at the cim section Containing the hole and at the cross sechon Gntaning the fillets when it's subjected to a tension of. tam while: P- 30 kN P. W= 52 mm t- 4 mm he 24 mm 14 mm de 22 mm k: 90 mm %3D S: Lile mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. %3D Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. %3D When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 1500 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L1 P L2 A Aluminum В d Copper c'P Answer: AL = in. %3D
The aluminum rod AB (Gal = 27 GPa) is bonded to %3D the brass rod BD (Gpr = 39 GPa). The portion CD of %3D the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T. 60 mm 2T 36 mm T 250 mm 375 mm 400 mm
The brass wire has a triangular cross section, 2mm on a side. The yield stress for brass is Ty= 208 MPa. Gbr= 37 GPa. Determine the maximum torque to which it can be subjected so that the wire will not yield and the angle of twist
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
HW:B Find the max Value of e) that canbe aPPIied on the Catilever beam Shown in figure , knowing that the max Gombined stresses will not exceed(22.67 Ma)in tension and (17.33 Ma) in wmPression? Ans/ Prnx = 25 W 450mm 150mm N.A Son S0mm fig. (B)
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
A uniform bar is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P = 7kN Determine the axial deformation of uniform bar 1 (in mm) Indicate negative sign if compression. Complete solution no round off.
Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. 4 m a -1 m 100 KN 250 mm 1 600 mm 200 mm Section a-a
The copper rod AB and steel rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T1 = 17°C, determine the average normal stress in each member when T2 = 47°C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm?. %3D Сopper Steel Elastic Modulus (GPa) 120 200 Coefficient of thermal expansion (1/°C) 17x10-6 12x10-6 В 1 m 0.6 m-
The bar ABCD is supported by a pin at A, a steel wire at B, and aluminum wire at D. Deterine the stress in steel and aluminum. Steel Aluminum A = 200 mm? L = 1.50 m A = 100 mm? L= 1.50 m E = 200 GPa E = 72 GPa B D P = 80 KN 1.50 m 1.25 m 0.75 m
When the temperature is at 30°C, the steel pipe fits snugly between the two fuel tanks. When fuel flows through the pipe, it causes the temperature to vary along the pipe as T = (3x² 20x + 120)°C. Calculate the normal stress developed in the pipe. Assume each tank provides a rigid support at A and B. a=12X10-6/°C - 150 mm 10 mm- Section a - a -6 m a a B