The bar ABCD is supported by a pin at A, a steel wire at B, and aluminum wire at D. Deterine the stress in steel and aluminum. Steel Aluminum A = 200 mm? L = 1.50 m A = 100 mm? L = 1.50 m E = 200 GPa E = 72 GPa A B D P = 80 KN 1.50 m 1.25 m 0.75 m

The bar ABCD is supported by a pin at A, a steel wire at B, and aluminum wire at D. Deterine the stress in steel and aluminum. Steel Aluminum A = 200 mm? L = 1.50 m A = 100 mm? L = 1.50 m E = 200 GPa E = 72 GPa A B D P = 80 KN 1.50 m 1.25 m 0.75 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if P=15 kN
The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied.
Axial loads are applied to the compound rods that composed of an aluminum segment rigidlyconnected between steel and bronze segments. If P = 25 kN, determine the following: a. Stress in the bronze segment. b. Stress in the aluminum segment. c. Stress in the steel segment.
A steel tube is rigidly attached between an Al rod and a bronze rod. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress of 80MPa in Al, 150MPa in steel and 100 Mpa in bronze. -1.0m 200 mm² 2.0m Steel 400 mm² 2P -2.5 m Bronze 500 mm²
The rigid beam is supported by a pin at B and wires AD and CE. (Figure 1) The load P on the beam causes the end A to be displaced 7.5 mm downward. The wires are unstretched when the beam is in horizontal position. Figure 3 m 2 m -2 m 1.5 m E 1 of 1 2 m ▼ Part A Determine the normal strain developed in wire CE. Express your answer in millimeters per millimeter to three significant figures. ECE = Submit Part B E AD = Submit D Provide Feedback AEO Ivec Request Answer Determine the normal strain developed in wire AD. Express your answer in millimeters per millimeter to three significant figures. AE Ivec S ? Request Answer mm/mm ? mm/mm
Q2: The pin-coected structure shown in figure below consists of a rigid member BED and three steel rods (E- 200 GPa). Each of the rods AB and CD has a 200 mm cross-sectional area and rod EF has a 625 mm2 cross-sectional area. If a load of P- 36 KN is applied at E, determine: (a) the change in length of rod EF. (b) the stress in each rod. 300 mm P-36 kN 300 mm 400 mm * 500 mm
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises after a load W = 120 kN is applied. Steel rod Bronze rod A (mm²) 350 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83 O Steel 1.5 m 1.0 m- 2.5 m 9. Determine the stress at the steel rod in MPa when there is a temperature rise of AT = 36 °C. W Bronze 3 m 1.5 m-
A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
Determine the normal stress (in Mpa) in member AC of the truss shown if it is made up of a 22-mm-square bar of alloy and the load P is 20.15 kN. Express your answer in two decimal places.
The shaft is made of A992 steel. It has a diameter of 0.7 in. and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for the material is 11 × 10³ ksi. 2 ft < 5 of 7 Part A B 2.5 ft > 60 lb-ft C 3 ft O 60 lb-ft
(a) Determine the bar force at FE(b) Determine the bar force at FN
Determine the maximum tensile and compressive stress in the beam. 1600 lb 4000 lb 7 in N.A. 2 in 3 ft T R1 6 ft 6 ft R2 Ina = 84 in