Q2: The pin-coected structure shown in figure below consists of a rigid memberBED and three steel rods (E- 200 GPa). Each of the rods AB and CD has a200 mm cross-sectional area and rod EF has a 625 mm2 cross-sectional area.If a load of P- 36 KN is applied at E, determine:(a) the change in length of rod EF.(b) the stress in each rod.300 mmP-36 kN300 mm400 mm *500 mm

Solution: Given Data E=200 Gpa P=36 kN (a) The charge in length of rod EF Let,P1=Reaction force at…

2: The pin-connected structure shown in figure below consists of arigidn BED and three steel rods (E-200 GPa). Each of the rods AB and Ci 200 mm? cross-sectional area and rod EF has a 625 mm? cross-section If a load of P- 36 kN is applied at E, determine: 3) the change in length of rod EF. b) the stress in each rod. 300 mm P-36 kN 300 mm 400 mm s00 mm

2: The pin-connected structure shown in figure below consists of arigidn BED and three steel rods (E-200 GPa). Each of the rods AB and Ci 200 mm? cross-sectional area and rod EF has a 625 mm? cross-section If a load of P- 36 kN is applied at E, determine: 3) the change in length of rod EF. b) the stress in each rod. 300 mm P-36 kN 300 mm 400 mm s00 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Punch Aluminum =4 mm d-20 mm

A: Given that t=4 mmd= 20 mmUltimate shear stress = 280 Mpa

Q: o Given: A stepped shaft with the following properties Copper: A = 2 in² E = 16 × 106 psi Steel: A =…

A: Given Copper and steelArea and Elasticity modulus of copper is 2 in2 and 16×106 psiArea and…

Q: The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part…

Q: 2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as…

A: Given data Area of steel=300mm2=300×10-6 m2 Area of aluminium=300mm2=300×10-6 m2 Area of…

Q: A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two-…

Q: Brass Problem 3: A composite bar is made by attaching a copper rod of length 900 mm and diameter 30…

Q: A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which…

Q: d. the normal stress in region BC. Is the material within its linear-elastic region? Yes / No A…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: An aluminum tube with the hexagonal cross-section shown is 2.5 ft long and has a constant wall in.…

A: Given data- An aluminium tube with hexagonal cross section Length (L) = 2.5 ft Constant Wall…

Q: The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: In the stepped shaft given in the figure, what will then be the P force provided that the stress in…

A: Given data in question Load 120 kNDiameter 50 and 75 mmLength750 & 1000 mmTo find out Load P

Q: AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS…

Q: Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a…

A: Determine the normal stress (in Mpa) in member AB

Q: H.W2: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig.…

Q: Aluminum Вгonze A= 300 Steel A=100 A=200 ЗР 5P 2P 25m 2.0 m 1.5 m

A: There are three types of rods used in construction generally. They are Steel, Aluminum, and bronze…

Question

Q2: The pin-coected structure shown in figure below consists of a rigid member
BED and three steel rods (E- 200 GPa). Each of the rods AB and CD has a
200 mm cross-sectional area and rod EF has a 625 mm2 cross-sectional area.
If a load of P- 36 KN is applied at E, determine:
(a) the change in length of rod EF.
(b) the stress in each rod.
300 mm
P-36 kN
300 mm
400 mm *
500 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Further calculation

VIEW

Step 3: Stresses in the rod

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 1 A rigid bar AC is loaded and supported as shown. Bar AB and CD are unstressed before the load is applied. Bar AB is made of steel (E = 30000ksi) and has a cross-sectional area of 1.25 in?. Bar CD is made of brass (E = 15000ksi) and has a cross-sectional area of 0.75 in². Determine: %3D 12 k/ft (1) The stresses in bars AB and CD (2) The vertical displacement (deflection) of C relative to the displacement at point (Note: express your answer in inches and include a direction) TI!||! 3 ft 4.5 ft
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1260 μm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. 1413 μm/m 1223 μm/m 1286 μm/m 738 μm/m 1553 μm/m
A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
It is made of solid circular cross-section bars, whose geometry and loading condition are given in Figure 2. The system formed is made of steel material and the torsional moments is under the influence. The diameter of the AB part of the rod is 100 mm; The diameter of the BC part is 60 mm. the shear modulus of steel is G = 80000 MPa. a)Draw the torsional moment diagram of the rod. b)Calculate the maximum shear stress that will develop in the system. c)Calculate the relative rotation value of point C with respect to point A b. M2 (kN.m) M1 (kN.m) B. A 100 mm 60 mm C а-а b-b L3 (mm) L4 (mm) kesiti kesiti Şekil 2 M1 (kN.m) M2 (kN.m) L3 (mm) L4 (mm) 60 50 600 700
The rigid bar AD is pinned at A and attached to the bars BC and ED, as shown below. The entire system is initially stress free and the weights of all bars are negligible. The temperature of bar BC is lowered 25°C and that of the bar ED is raised 25°C. Neglecting any possibility of lateral buckling, find the normal stresses in bars BC and ED. For BC, which is brass, assume E = 90GPa, a = 20x 10-6/°C, and for ED, which is steel, take E = 200 GPa and a = 12x10-6/°C. The cross-sectional area of BC is 500 mm2 and of ED is 250 mm2.
Please show your solution on a paper with FBD
Determine the normal stress (in Mpa) in member AC of the truss shown if it is made up of a 22-mm-square bar of alloy and the load P is 20.15 kN. Express your answer in two decimal places.
answer problem 2 only
A rigid bar AB is pinned at end A and issupported by a wire CD and loaded by a force P atend B (see figure). The wire is made of high-strengthsteel having a modulus of elasticity E = 210 GPa andyield stress σY =820 MPa. The length of the wire isL =1.0 m, and its diameter is d =3 mm. The stress straindiagram for the steel is defined by the modifiedpower law, as σ =Eε 0<σ≤σy σ = σy[Eε/σy] σ≥σy (a) Assuming n = 0.2, calculate the displacementδB at the end of the bar due to the load P. Takevalues of P from 2.4 kN to 5.6 kN in incrementsof 0.8 kN.(b) Plot a load-displacement diagram showing Pversus δB.
The pin is used to connect the three links together. Due to wear, the load is distributed over the top and bottom of the pin as shown on the free-body diagram. The diameter of the pin is d = 11.4 mm. (Figure 1) Part A Determine the maximum bending stress on the cross-sectional area at the center section a-a. For the solution it is first necessary to determine the load intensities wi and w2 Express your answer to three significant figures and include the appropriate units. HA ? Omax = Value Units Submit Request Answer Figure 1 of 1 < Return to Assignment Provide Feedback 3600 N W2 W2 25 mm 25 mm 40 mm 1800 N 1800 N
A steel tube is rigidly attached between an Al rod and a bronze rod. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress of 80MPa in Al, 150MPa in steel and 100 Mpa in bronze. -1.0m 200 mm² 2.0m Steel 400 mm² 2P -2.5 m Bronze 500 mm²