Determine the convection heat transfer coefficient (in W/m2-K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10:5 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x105 0.7296

Determine the convection heat transfer coefficient (in W/m2-K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10:5 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x105 0.7296

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Combustion gases passing through a 5-cm-internal-diameter circular tube are used to vaporize waste water at atmospheric pressure. Hot gases enter the tube at 225 kPa and 250oC at a mean velocity of 2.5 m/s, and leave at 150o If the average heat transfer coefficient is 150 W/m2K and the inner surface temperature of the tube is 110oC, determine (a) the tube length and (b) the rate of evaporation of water.
solve, show assumptions and full solutions
Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cm-ID tube whose surface is maintained at 620 K. What length of tube is required?
In a dairy operation, milk at a flow rate of 0.25m3/hr and a cow-body temperature of 38.6°C must be chilled to a safe-to- store temperature of 13°C. Cold water at 2.2°C is available at a flow rate of 0.94m3/hr. The density and specific heat of milk are 1030 kg/m3 and 3860 J/kg.K, respectively. The density and specific heat of water is 1000 kg/m3 and 4187 J/kg.K. The chilling process is done by a double pipe counter-flow exchanger with an overall heat transfer coefficient U=1000 W/m2.K. The pipe of the heat exchanger has a 50-mm diameter with negligible thickness. Determine the pipe length L required. Select one: O a. 2.28 m O b. 4.28 m O c. 3.28 m O d. 1.28 m
air is flowing inside of a pipe with radius=0.4 meters at a mass velocity of 29.4 kg/s*m2 at 322 K, with the walls of the pipe at 300 K. At the conditions of the experiment, the viscosity of air is 1.984 x 10-5 Pa*s, the density of air is 1.22 kg/m3, the heat capacity is 1 kJ/kg*K, and the thermal conductivity is 0.025 W/m*K. Determine the rate of heat loss by air per meter of duct.
A gas flows over a heated horizontal surface with a surface temperature that is uniform and higher in value than the temperature of the gas. The local convective coefficient in W/m².K of this flow with convective heat transfer can be given as a function of the distance x (in meters) from the beginning of the horizontal surface by: h = A xD + B x + C, where A = -2.4, B = 14.8, C = 9.3 and D = 2.7. Based on this information, calculate the average Nusselt number of the flow over the plate if it is three meters long. Consider: ρgas = 0.9950 kg/m³; kgas = 30 x 10-3 W/m.K. Note: Use the equations given in the book by Schmidt et al. for problem resolution.
Consider a pipe with a length of 25 m and diameter of 5 cm. The surface temperature of the pipe is constant at 150°C.Oil at 20°C is passing though this pipe with a mass flow rate of 0.5 kg/s. determine (a) the temperature of the oil at the exit and (b) the total heat transfer rate. Note. Report your solution step by step and clearly.
Parvinbhai