Consider a pipe with a length of 25 m and diameter of 5 cm. The surface temperature of the pipe is constant at 150°C.Oil at 20°C is passing though this pipe with a mass flow rate of 0.5 kg/s. determine (a) the temperature of the oil at the exit and (b) the total heat transfer rate.

Consider a pipe with a length of 25 m and diameter of 5 cm. The surface temperature of the pipe is constant at 150°C.Oil at 20°C is passing though this pipe with a mass flow rate of 0.5 kg/s. determine (a) the temperature of the oil at the exit and (b) the total heat transfer rate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Liquid ammonia at -20°C (rho= 665.1 kg/m³ and μ = 2.361*10-4 kg/m*s) is flowing through a 20 m long section of a 5 mm diameter copper tube with friction factor 0.01819 at a velocity of 9.19 m/s and differential pressure of 2043.05 kPa Liquid then the pumping power required to push the liquid is W L D T
8.62, 8-62 Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b = 25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.01 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C.
Water at 15°C is to be heated to 65°C by passing it over a bundle of 4-m-long, 1-cm-diameter resistance heater rods maintained at 90°C. Water approaches the heater rod bundle in normal direction at a mean velocity of 0.8 m/s. The rods are arranged in-line with longitudinal and transverse pitches of SL=4 cm and ST=3 cm. Determine the number of tube rows NL in the flow direction needed to achieve the indicated temperature rise. Please, I need the solution from fundamental concepts of how the heat flow behaves in the system. That it be answered with theory of the subject
The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of fluid at the inlet are 3,050 kJ/kg and 241 km/hr respectively. At the exit the specific enthalpy of fluid is 2,632 J/kg. Calculate the rate of flow of fluid (mass flow rate) when the inlet area is 0.22 m2 and the specific volume at the inlet is 0.31 m3/kg.
In a geothermal power plant, the used geothermal water at 80°C enters a 15-cm-diameter and 400-m-long uninsulated pipe at a rate of 8.5 kg/s and leaves at 70°C before being reinjected back to the ground. Windy air at 15°C flows normal to the pipe. Disregarding radiation, determine the average wind velocity in km/h.
What are the factors that affect the value of Friction factor in Laminar flow and Turbulent flow?
A condenser consists of several tubes. The outer diameter of each tube is 2 cm, and the thickness is 2 mm. It is designed to condense saturated steam that enters the condenser at the mass flow rate of 100 kg/s. The steam pressure is 10 kPa. There is 10% moisture in saturated steam. The inlet temperature of cooling water is 20°C, and the outlet temperature is 40°C. Water velocity 2 m/s. The overall heat transfer coefficient based on outer surface area is 3.5 3. kW/m2.K. The heat capacity of water is 4.2 kJ/kg.K. Water density is 1000 kg/m'. Find the number of tubes and the length of each tube.
Hot air at 1 bar and 80 degree Celcius enters a 8 m long uninsulated square duct of cross-section 20 cm x 20 cm that passes through the attic of a house at a rate of 150 L/s. The duct is observed to be constant surface temperature of 60 degrees Celcius. Determine (a) air film coefficient (b) the exit temperature of air (c) logarithmic mean temperature difference (d) the rate of heat loss from the duct to the attic space. From Table A-18, for air gives, density, ρ = 1.009 kg/m^3thermal conductivity, k = 0.0297 W/m degree celciusviscosity, v = 2.06 x 10^-5 m^2/sspecific heat, Cp = 1008 J/kg degree celciusPrandtl no., Pr = 0.706
A house built on a riverside is to be cooled in summer by utilizing the cool water of the river. A 15-m-long section of a circular stainless-steel duct of 20-cm diameter passes through the water. Air flows through the underwater section of the duct at 3 m/s at an average temperature of 15°C. For an overall fan efficiency of 62 percent, determine the fan power needed to overcome the flow resistance in this section of the duct.
The hot water needs of a household are to be met by heating water at 15°C to 95°C by a parabolic solar collector at a rate of 1.8 kg/s. Water flows through a 4-cm-diameter thin aluminum tube whose outer surface is blackanodized in order to maximize its solar absorption ability. The centerline of the tube coincides with the focal line of the collector, and a glass sleeve is placed outside the tube to minimize the heat losses. If solar energy is transferred to water at a net rate of 200 W per meter length of the tube, determine the required length of the parabolic collector to meet the hot water requirements of this house. Also, determine the surface temperature of the tube at the exit.
Consider an adiabatic duct of diameter 12 cm with inlet conditions of the velocity, temperature, pressure and Mach number as indicated in the figure below. Take the average friction factor to be 0.021. determine the duct length from the inlet where the inlet velocity doubles, also determine the pressure drop along that section of the duct. For air, take k = 1.4, specific heat at constant pressure and gas constant to be 1.005 kJ/kg-K and 0.287 kJ/kg-K respectively. L P₁ = 200 kPa T₁ = 550 K Ma₁ = 0.4 + f=0.021 L Exit Ma₂=0.8 L₂Ⓡ Mal T* p
Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b= 25 mm, that is maintained at a constant surface temperature. Liquid water enters the tube at 20°C with a mass flow rate of 0.027 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C. (Nu = 3.39) "C