determine the allowable bending and contact stresses for a grade 1 steel through-hardened to 250 HB. Assume the desired reliability is 50% and that the pinion and gear have the same hardness and the gear encounters hydrodynamic lubrication and is to last ten million cycles

determine the allowable bending and contact stresses for a grade 1 steel through-hardened to 250 HB. Assume the desired reliability is 50% and that the pinion and gear have the same hardness and the gear encounters hydrodynamic lubrication and is to last ten million cycles

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Don't give handwritten
A helical cast steel gear with 30° helix angle has to transmit 35 kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary module, pitch diameters and face width for 20° full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times the normal pitch. The tooth form factor is given by the expression y'=0.154– 0.912/T; , where Tg represents the equivalent num- ber of teeth. The velocity factor is given by C, where 6 + v v is the peripheral speed of the gear in m/s.
1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW, Ni 1450r /min, and the %3D transmission ratio is required to be u = 2.08. F1. If there is slight impact, the supplementary conditions for trial design of this pair of gears: primary selection k = 1.8, number of smaller gear teeth Z1 = 26. The allowable stress and factors for material %3D is: [0]= 600 MPa, [o„]z= 599 MPa, [0,]ı= 220 MPa, [0,]= 213 MPa. E=1.693, Z, =1898/mpa Z„ = 2.5 K =1.25 Ky =1.1 K K =1.2 На K =1.35 Y =2.65, Y = 2.28 Y =1.58 Y =1.76 %3D Fa2 Fal sa1
A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.
A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the pinion pitch and the gear is 80 mm and 100 mm. The shape of the gear gear was 14 restriction form. The static voltage allowed for both gear is 55 mpa. If the door transports to 2.95 kw power at the turn of 1200 RPM, identify the module and the number of teeth on each gear from the Angle of power and check the design from the Angle of the tear. Take the surface durability limit is 630 mpa and the modulus elasticity to iron cast is 84 kn /mm2.
A drive system for a large commercial band saw is to be designed to transmit 12 hp. The saw will be used to cut steel tubing for automotive exhaust pipes. The pinion rotates at 3450 rpm, while the gear must rotate between 725 and 735 rpm. Specify appropriate material and hardness that will make gears safe in bending and pitting. Case hardening is not to be used.
If a pinion having 20 teeth transmit the power to the gear shaft having 40 teeth, the gear ratio of this system is 0.5. Select one: O True O False Stress concentration factor is defined as the ratio of the lowest stress or nominal stress in the component to the highest stress any where in the same component. Select one: O True O False A radial ball bearing fitted on to the shaft of a refinery vessel is subjected to axial load of 3340.8 N, take the service factor(K;) as 1.5. The equivalent dynamic load acting on the bearing will be . O 10022.40 O 1670,40 O 2505.60 O 5011.20 The outer diameter of muff is calculated as 81.2 mm. The shaft diameter of muff coupling is . mm. O a. 39.60 O b. 34.10 O c.61.38 O d. 26.80
If in a gear design problem, the required hardness of steels per allowable gear bending strength is: HB = 158; while the required hardness of steels per allowable gear contact strength is: HB = 256. Which material HB hardness will be used for gear material specification? 256 158 120 400
2. A spur gear made of bronze drives a mid steel pinion with angular velocity ratio of 3, : 1. The pressure angle is 142. It transmits 5 kW at 1800 r.p.m. of pinion. Considering only strength, design the smallest diameter gears and find also necessary face width. The number of teeth should not be less than 15 teeth on either gear. The elastic strength of bronze may be taken as 84 MPa and of steel as 105 MPa. Lewis factor for 142 pressure angle may be taken as 0.684 0.124 - y = No. of teeth
Solve correctly please. Should 100% sure
A gear drive consists of a 16-tooth 20° steel spur pinion and a 48-tooth cast-iron gear having a pitch of 12 teeth/in. For a power input of 1.35 hp at a pinion speed of 700 rev/min, select a face width based on an allowable contact stress of 100 kpsi. Refer to table number 14-8 for elastic coefficient. The face width based on an allowable contact stress of 100 kpsi is in.
A gear drive is required to transmit a maximum power of 22.5KW, the velocity ratio is 1:2 and the rpm of the pinion is 200 .the approximate center distance between the shaft may be taken as 600mm.the teeth has 20°stub involute profile.the static stress for the gear material ( which is cast iron ) may be taken as 60MPa and face width as 10 times the module.find the module, face width and number of teeth on each gear.Check the design for dynamic and wear loads. The deformation factor in the buckling equation may be taken as 80 and material combination factor for the wear as 1.4