Design the elliptical cross-section of a belt pulley arm near the hub for the following specifications: The mean pulley diameter is (300 mm) and the (number of pulley arms are 4). The elliptical section has major axis twice the minor axis length. The tight and slack sides tension in the belt are (600 N and 200 N) respectively. Assume half number of arms transmit torque at any time and the load factor of 1.75 to account for dynamic effects on the pulley while transmitting torque. The permissible tensile stress for cast iron pulley material is 15 MPa. The pulley hub diameter is 60 mm.

Design the elliptical cross-section of a belt pulley arm near the hub for the following specifications: The mean pulley diameter is (300 mm) and the (number of pulley arms are 4). The elliptical section has major axis twice the minor axis length. The tight and slack sides tension in the belt are (600 N and 200 N) respectively. Assume half number of arms transmit torque at any time and the load factor of 1.75 to account for dynamic effects on the pulley while transmitting torque. The permissible tensile stress for cast iron pulley material is 15 MPa. The pulley hub diameter is 60 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A helical compression spring is to be cycled between 150 lbf and 300 lbf with a 1-in stroke. The…

A: (Bartleby policy): Since you have posted a question with multiple sub-parts, we will solve the first…

Q: a) An angular contact ball bearing for mounting at O a b) A straight roller bearing for mounting at…

A: Solution : Given data : F_A = 600 lbf N = 420 rev/min from table 11-2 for…

Q: . Design a roller chain drive. Specify the chain size, the sizes and number of teeth in the nrockets…

A: given: kW=29.8 n1=500 rpm n2=250 rpm For durability and noise consideration…

Q: Problem 4. A 16-tooth 240 Bhn steel spur pinion having a pressure angle of 20° and rotating at 720…

A: Calculate the diameter of the gear. Dg=NgPg Here, Dg is the gear diameter, Ng is the number of teeth…

Q: Drawing 1 of Figure P8.51 shows a countershaft with helical gear (B), bevel gear (D), and two…

A: Given:-Shaft with helical gear with different loading conditionSu=1069 MPaSy=896 MPaTo find:-a)…

Q: A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800…

A: Given:T = 800 N-mDo = 150 mm = 0.150mDi = 90 mm = 0.09mpmax =1000 kPaf = 0.10To findTotal number of…

Q: Q1/A 6-in-wide polyamide F-1 flat belt is used to connect a 2-in-diameter pulley to drive a larger…

A: This question is related to the flat belts.The expression of angle of contact of the pulley.Here, C…

Q: mechanism like this one, if it is known the length of O2A (link 2) is 5 cm (link 3) is 4 cm (link 3)…

Q: The following figure depicts a 1600 rpm motor, gear box, and 4000 rpm blower. The gear box weighs 40…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: A1. A flat belt drive for speed reduction has pulley diameters of 200 mm and 380 mm. The maximum…

A: The diameter of pulleys = 200 mm and 380 mmThe maximum tension F₁ = 620 NThe power transmitted, P =…

Q: lical compression spring is wound using 0.12-in-diameter phosphor-bronze B159 wire. The spring in 10…

Q: 3. Calculate the torque and the rotation speed at the input pulley if the output pulley needs to…

A: (a) The torque at the input pulley is 66.67 lb•in. (b) The rotational speed of the input pulley is…

Q: The compound gear train of a three stages reduction gear is use to transmit power from a power…

A: Given DataN1=500…

Q: A 20° 20-tooth cast-iron spur pinion having a module of 4 mm drives a 32-tooth cast-iron gear. Find…

Q: Required information A helical coil compression spring is needed for food service machinery. The…

A: helical coilExplanation:Step 1:Step 2:Step 3: Step 4:

Q: 3)Design a V – Belt drive to the following specifications Power transmitted = 75kw Speed of driving…

Q: Required information A helical coil compression spring is needed for food service machinery. The…

A: helical coilExplanation:Step 1:Step 2:Step 3:Step 4:

Q: A hammer mill is driven by a High Torque (HT) AC motor. The system is used for 8 hours /day. Input…

A: Diameter of the motor shaft pulley = D1 = 1.33 cube root of Power / Speed max D1 = 1.33 cube root 25…

Q: Provide step-by-step solution with complete given and formula to this problem. Draw sketch also.…

A: Given DataL=328 ftd=1.75 inW=8×103×2.2=17.6×103 lbsV=525 fpmt=10s

Q: Analyze the existing condition of the crank in a four- bar linkage. Draw a quick-return mechanism.…

A: A quick return mechanism is a device that generates a reciprocating motion in which the return…

Q: Q4/A single V belt is to be selected to deliver engine power to the wheel-drive transmission of a…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

•
HOME WORK
Design the elliptical cross-section of a belt pulley arm near the hub for the
following specifications: The mean pulley diameter is (300 mm) and the
(number of pulley arms are 4). The elliptical section has major axis twice
the minor axis length. The tight and slack sides tension in the belt are (600
N and 200 N) respectively. Assume half number of arms transmit torque
at any time and the load factor of 1.75 to account for dynamic effects on
the pulley while transmitting torque. The permissible tensile stress for cast
iron pulley material is 15 MPa. The pulley hub diameter is 60 mm.
[Ans. a=40 mm, b₁= 20 mm]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: The given values are below :

VIEW

Step 2: The elliptical cross section of the belt pulley is :

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

EQUATION SHEET TABLE A-9 LINKS BELOW bartleby doesn't allow more than 2 pic uploads so i attached them
For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each driven by a DC motor of 10,500 HP operating at 125 RPM. For your ASSIGNED gearbox only, you are required to analyze the gearbox capabilities by doing thefollowing: 1. Calculate the maximum motor torque2. calculate the force transmitted by the gearing.3. Using statics, calculate the equivalent radial load at the bearings for BOTH the pinion shaft and the gear shaft. (Four bearings total; two per shaft). Include FBDs of the shafts.4. Research the load capacities for the bearings.(Hint: the bearing manufacturer is most likely Timken / Torrington).5. Calculate the expected bearing life for each bearing.6. Calculate the safety factor for both the bending strength and the pitting resistance for the pinion shaft AND the gear shaft gear teeth based on the transmitted load and the gear material(s).7. Draw the shear, bending moment, and torque diagrams for the GEAR SHAFT ONLY.8. Calculate the…
Design a crank-rocker mechanism with a time ratio of Q = 1.34, throw angle of (θ4)MAX= 85°, and time per cycle of t = 4.8s. Specify the link lengths and crank speed
Please help with all thank you!!
An electric motor running at 970rpm is used to drive a rock crushing machine with a design power of 32 kW. A 33oz ducking weight flat belt drive is proposed with a tension ratio of R = 4 and belt width b = 120 mm. The pitch diameter of the driving pulley (on the motor-end) is 320mm. a) What is the mass per mm width per m length per ply in kg/mm/m/ply? Number (exact value) b) What is the maximum working tension per mm width per ply in N/mm/ply? Number (exact value) c) Calculate the belt velocity in m/s Number (+/-1%) d) Determine the number of belt plies required. Your answer should be an integer number (no decimals). Number (exact value)
show all steps and solution
A four-part mechanism like this one, if it is known the length of o2a (link 2) is 5 cm (link 3) is 4 cm (link 3) and the length of the bo4 (link 4) is 5.5 cm (5 in.). At the a point working the p = 50 Newton style with the sustric orientation of the horizontal line is 20⁰, look for styles that are going on and torque on link 4.
Solve show solution
The picture shows the rear swivel axle bearing design of a 4-wheel wagon. It is known that the speed of the wagon wheels is n = 37 rpm. The total radial load carried by the wagon is given as Fr= 16060 Newtons. In addition, due to road conditions, Fa axial load is applied to the wagon. If the axial load on the A bearing is 10% of the radial (vertical) load on this bearing, calculate the dynamic load number (C) of the bearing in the A bearing in Newtons for 18616 hours of life. fo*Fa/Co = 0.345 Pi=3.14