cure 1 of 1 D 60° 4m < > If load C has a mass of 380kg, determine the required minimum diameter of the solid L2-steel rod AB to the nearest mm so that it will not buckle. Use F. S.= 1.94 against buckling. (Figure 1) Express your answer with the appropriate units. Submit HA Value Units My Answers Give Up ? Provide Feedback Continue

cure 1 of 1 D 60° 4m < > If load C has a mass of 380kg, determine the required minimum diameter of the solid L2-steel rod AB to the nearest mm so that it will not buckle. Use F. S.= 1.94 against buckling. (Figure 1) Express your answer with the appropriate units. Submit HA Value Units My Answers Give Up ? Provide Feedback Continue

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The linkage is made using two A992 steel rods, each having a circular cross section. If each rod has a diameter of 0.85 in .. (Figure 1) Figure 1 12 ft of 1 B 45° 30° Part A Determine the largest load it can support without causing any rod to buckle. Assume that the rods are pin connected at their ends. Express your answer to three significant figures and include the appropriate units. μA Pmax = 354.255 lb ?
As shown, three steel wires, each 26 mm in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M- 1,041 kg. what stress exists in the MIDDLE (the second longest) wire? Use E-215 Gpa. Answer must be in MPa. ions es eButton Danila Library Presentation ictery Survey
Q2] Determine the value of W that may cause the pinned column AB with the pipe section shown to buckle. The column is constructed of a material for which E= 20 GPa. Also, find the safety factor against failure by buckling If Gall= 6.5Mpa W 100 D + 5 m Column cross-section Outer diameter (D)=100mm Thickness (t)=10 mm C K 2.5 m B 2.5 m 'V'
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
The maximum allowable tensile force in the members of the truss is (Ft)max = 1700 lb, and the maximum allowable compressive force is (Fe)max = 1000 lb. (Figure 1) Figure 1 of 1 Part A Determine the maximum magnitude P of the two loads that can be applied to the truss. Take a = 8 ft. Express your answer in pounds to three significant figures. P = Submit Provide Feedback Π| ΑΣΦ ↓↑ vec Request Answer C ? lb
Figure 2 m -2 m- -3 m- www 1 of 1 B The spring DB has an unstretched length of 2 m. (Figure 1) ▼ Part A Determine the stiffness of the spring to hold the 90-kg crate in the position shown. Express your answer to three significant figures and include the appropriate units. k = 198 Submit uA kg Previous Answers Request Answer ? X Incorrect; Try Again; 3 attempts remaining
Two vertical rods AB (A36 steel, E = 200 GPA) and CD (red brass, E = 101 GPA) support a rigid bar AC which is loaded at E. In the current configuration workers in the factory have noticed the horizontal bar AC rotates slightly once the load in E is applied. This is causing problems and needs to be addressed. Your supervisor has asked you to first verify that this rotation is occurring and calculate its magnitude. Then determine the new location for the load application point E such that this rotation can be eliminated.
The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can be approximated as shown. The wing is subjected to a torque of 4.7 MN m and the wall thickness is 10 mm. The wing is made of 2014-T6 aluminum alloy. Figure 1 of 1 0.5 m 10 mm 10 mm 10 mm 2 m 0.25 m 0.25 m Express your answer with the appropriate units. Tavg 124 MPa Submit Correct Part B My Answers Give Up Determine the angle of twist per meter length of the wing. Express your answer with the appropriate units. VΠΙ ΑΣΦ It vec Submit My Answers Give Up Incorrect; Try Again; 5 attempts remaining ? °/m
Figure Lat -1 ft-- B 4 ft -1 ft- 1 of 1 Determine the normal force that the 120-lb plate A exerts on the 40-lb plate B. Express your answer to three significant figures and include the appropriate units. NAB = Submit Provide Feedback μA Value Request Answer Units ?
You are designing a suspension linkage rod for a new sports car. It will be 12 inches long and fixed-pinned at the ends. The rod must support an axial load of 10 kips (compression). Design the smallest solid circular aluminum rod (diameter rounded to the nearest 0.1 inch), to prevent both buckling and yield failure. Use a factor of safety of 3.0 with respect to both buckling and yield. Assume Aluminum E = 10000 ksi, o, = 40 ksi. %3D [Formula: Axial Loading: Normal Stress o = (P)/(A); Axial Deformatipn 8 = (P)(L/(AE); Buckling Capacity: Per = (r')(EI)/(k*L)’, where 'k' is effective length factor] %3D L= 12 in Fixed-Pinned
An elliptical gate covers the end of a pipe 4m in diameter. Of the gate is hinged at the top, what normal force F is required to open the gate when water is 8m deep above the top of pipe and the pipe is open to the atmosphere on the other side? Neglect the weight of the gate. Find: ħ in kPa Agate in m2 FR in kN ȳ in m I in m4 ycp in m F in kN
The polyvinyl chloride bar is subjected to an axial force of 000 lb. The angle e decresses by A0 - 0.01° afier the load is applied. Epre - 800(10) psi. (Figure 1) Part A it the bar has the onginal dimensions shown determine the value of Poisson's ratio. Express your answer using three significant figures. Submit Request Answer Figure 1 of 1 Provide Feedback 900 900 h 3in