Correct answer and complete fbd only. I will upvote. A flanged bolt coupling consists of two concentric rows of bolts. The inner row has 6 nos. of 16mm diameterbolts spaced evenly in a circle of 250mm in diameter. The outer row of has 10 nos. of 25 mm diameter bolts spaced evenly in a circle of 500mm in diameter. If the allowable shear stress on one bolt is 60 MPa, determine the torque capacity of the coupling. The Poisson’s ratio of the inner row of bolts is 0.2 while that of the outer row is 0.25 and the bolts are steel, E =200 GPa.

Correct answer and complete fbd only. I will upvote. A flanged bolt coupling consists of two concentric rows of bolts. The inner row has 6 nos. of 16mm diameterbolts spaced evenly in a circle of 250mm in diameter. The outer row of has 10 nos. of 25 mm diameter bolts spaced evenly in a circle of 500mm in diameter. If the allowable shear stress on one bolt is 60 MPa, determine the torque capacity of the coupling. The Poisson’s ratio of the inner row of bolts is 0.2 while that of the outer row is 0.25 and the bolts are steel, E =200 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

please provide fbd for the solution. I need to review this question. Thank you!
Write legibly, provide manual step by step solution, and diagram for below given problem. A flange bolt coupling has 10 steel coupling 1 inch diameter bolts evenly tighten around a 16.34in. bolt circle. Determine the torque capacity of the connection if the allowable shearing stress in the bolt is 7.3ksi? Ans. 39,034.94 ft-lb
1) A pair of cast iron bevel gears connect two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm respectively. The tooth profiles of the gears are of 14 1/2° composite form. The allowable static stress for both the gears is 55 MPa. If the pinion transmits 2.75 kW at 1100 r.p.m., find the module and number of teeth on each gear from the standpoint of strength and check the design from the standpoint of wear. Take surface endurance limit as 630 MPa and modulus of elasticity for cast iron as 84 kN/mm². A0a& ENG 1222/20 nere to search
(Please input the FBD together with the answer) A flanged bolt coupling consists of nine-in diameter bolts equally spaced around a bolt circle 15 inches in diameter. Determine the torque capacity of the coupling if the shear stress in the bolt is limited to 5000 psi.
1.
Problem 1 shaft B A flanged bolt coupling has ten 12-mm diameter steel bolts on 450 mm diameter bolt circle and six 12 mm diameter bolts on 200 mm diameter bolt gircle. Determine the maximum torque (in KN-m) that can be applied without exceeding the shear stress of 60 MPa for each bolt. Use G = 80 GPa. V1 V2 R2 -coupling
Please I want answer of that question from these choices
.A flanged bolt coupling consists of six 12.5 – mm steel bolts evenly spaced around a bolt circle 300mm in diameter, and four 19 – mm aluminum bolts on a concentric bolt circle 200 mm in diameter.What torque can be applied without exceeding 62 MPa in the steel or 42 MPa in the aluminum?Assume Gst = 82.7 GPa and Gal = 27.6 GPa.
! Required information A torque T-130 N-m is applied to the shaft EFG, which is running at constant speed and contains gear F. Gear F transmits torque to shaft ABCD through gear C, which drives the chain sprocket at B, transmitting a force Pas shown. Sprocket B. gear C, and gear F have pitch diameters of a = 120 mm, b= 200.004 mm, and c= 100 mm, respectively. The contact force between the gears is transmitted through the pressure angle = 20°. 25 DEKO d-30mm 1-250 man 0 30 x-125+ The maximum principal normal stress is The maximum shear stress is Combine these stresses and determine the maximum principal normal and shear stresses in the shaft. MPa View ad MPa.
A 1.5 in diameter 10-spline shaft and permanent fit has a compressive force of 2000 lbs. Find the torque applied if hub length 2 in.
5.2 Please help. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
Ex: The second shaft on a parallel-shaft 25-hp foundry crane speed reducer contains a helical gear with a pitch diameter of S.08 in. Helical gears transmit components of force in the tangential, radial, and axial directions. The components of the gear force transmitted to the second shaft are shown in Fig. (8) at point A. The bearing reactions at C and D, assuming simple- supports, are also shown. A ball bearing is to be selected for location C to accept the thrust, and a cylindrical roller bearing is to be utilized at location D. The life goal of the speed reducer is 10 kh, with a reliability factor for the ensemble of all four bearings (both shafts) to equal 1 (90% reliability) with light to moderate impact. (a) Select the roller bearing for location D. (b) Select the ball bearing (angular contact) for location C, assuming the inner ring rotates. *- 20 Fig (8)