A flanged bolt coupling has ten 12-mm diameter steel bolts on 450 mm diameter bolt circle and six 12 mm diameter bolts on 200 mm diameter bolt gircle. Determine the maximum torque (in KN-m) that can be applied without exceeding the shear stress of 60 MPa for each bolt. Use G = 80 GPa.

A flanged bolt coupling has ten 12-mm diameter steel bolts on 450 mm diameter bolt circle and six 12 mm diameter bolts on 200 mm diameter bolt gircle. Determine the maximum torque (in KN-m) that can be applied without exceeding the shear stress of 60 MPa for each bolt. Use G = 80 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: (Please input the FBD together with the answer) A flanged bolt coupling consists of nine-in diameter…

A: The torque capacity of the flange coupling is 5522.33 lb•ft.

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD…

A: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksiThe sleeve CD is…

Q: The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate…

Q: The cylinder of a hydraulic ram supported at the open end is 200 mm internal diameter and is…

Q: The steel tube has a thickness of 11 mm and the dimensions shown below. If the applied torque is…

Q: A compound shaft consists of an outside tube (1) and an inner tube (2) that are fully connected…

Q: The shaft is made of A-36 steel and has a diameter of 70 mm. It is fixed at B and the support at A…

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: The given values are - do =75 mm, t=5 mm, T =4090×1000 Nmm, G =80×1000 Mpa, L=2000mm The inside…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

Q: The composite shaft shown consists of a solid brass segment (1) and a solid aluminum segment (2)…

A: Given:d1=15 mmL1=235 mmG1=4 GPad2=24 mmL2=165 mmG2=39 GPaT=270 N.m

Q: A flange bolt coupling consists of 7 38 mm diameter steel bolts spaced around a bolt circle 285 mm…

A: Number of bolts = 7 Diameter of bolts = 38 mm Diameter of bolt circle = 285 mm Polar modulus = J r =…

Q: 2. The diameters of the solid shafts are: AB is 0.6 in, BC is 0.75 in. and CD is 0.9 in. The applied…

Q: A circular solid shaft has a diameter of 60 mm and is subjected to a torque load of 8.7 kN•m.…

A: Given Diameter, d = 60 mm Torque load, T = 8.7 kN•m

Q: For each part of the shaft, determine the torsion T and calculate the corresponding maximum…

A: The diameter of the shaft is d=2 in

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

Problem 1
shaft
B
A flanged bolt coupling
has ten 12-mm diameter
steel bolts on 450 mm
diameter bolt circle and six
12 mm diameter bolts on
200 mm diameter bolt
gircle. Determine the
maximum torque (in KN-m)
that can be applied
without exceeding the
shear stress of 60 MPa for
each bolt. Use G = 80 GPa.
V1
V2
R2
-coupling

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm diameter solid brass (G = 37 GPa) rod. Segment (2) is a solid aluminum (G = 26 GPa) rod. Determine the minimum diameter of the aluminum segment if the rotation angle at C relative to support A must not exceed 5°. T= 60 N.m (1) (2) A B 1,800 mm 800 mm Select one: a. 21.55 mm O b. 10.77 mm O c. 11.88 mm O d. 23.77 mm e. 32.00 mm f. None
The following rod has a diameter of 15 mm, and a length of 1000 mm, and was fixed at its one end to the wall. A force pair of 200 N is applied by a 500 mm length arm to the point A. Which material given below should be chosen for this rod material to keep the twist angle on the A plane less than 20°. Material Aluminium alloy Magnesium alloy Titanium alloy E, GPa 70 45 105 V 0,3 0,3 0,3 200 N 250 mm 250 mm 200 N
The A36 steel shafts as shown in the figure below are made from two segments: solid segment AC with diameter = 1 in and a hollow segment CB with an outside diameter = 2 in and inside diameter = 1 in. The shaft is fixed at both ends. Determine the magnitude of the applied torque T (lb-in) if the reaction at A is 600 lb-in clockwise.
I am struggling with this question
Please and thank
4-Determine the rotation angle between A and C, if the torque is T=0.9 N.m in point C, if G=80 GPa and diameter of all shafts are D=4 mm. (The radius of small circle are r and the bigger one are 2r) e are Coder 40 T=09N.N
A 2in diameter shaft is made of aluminum 2014-T6, and has a torque of 1/2T, -T and 2/3T respectively along its length measured from the free end with the distance of 12 inches between its section. If the factor of safety of 3 is used and the angle of twist is limited such that it does not exceed 0.1 rad. find the maximum allowable tonque T in the shaft in ksi
A circular hollow shaft has outer diameter of 60 mm and thickness of 15 mm and is subjected to a torque load of 4.2 kN•m. Determine the resulting minimum shear stress. Also determine the resulting maximum shear stress.
The problem is stated below. However, change the position of torque to point C from point D. What is the effect of variation of torque placement in shaft CB?
The hollow shaft used in the system has the following conditions: Outer Ø:110 mmØ Allowable Shearing Stress:85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
The shaft consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the angle of twist developed at the interface of the two segments when the torque T = 50 kip٠in is applied. Use G = 4×106 psi for aluminum and G = 12×106 psi for steel.