Ex: The second shaft on a parallel-shaft 25-hp foundry crane speed reducer contains a helical gear with a pitch diameter of 8.08 in. Helical gears transmit components of force in the tangential, radial, and axial directions. The components of the gear force transmitted to the second shaft are shown in Fig. (8) at point A. The bearing reactions at C and D, assuming simple- supports, are also shown. A ball bearing is to be selected for location C to accept the thrust, and a cylindrical roller bearing is to be utilized at location D. The life goal of the speed reducer is 10 kh, with a reliability factor for the ensemble of all four bearings (both shafts) to equal 1 (90%% reliability) with light to moderate impact. (a) Select the roller bearing for location D. (6) Select the ball bearing (angular contact) for location C, assuming the inner ring rotates. Fig.(8)

Ex: The second shaft on a parallel-shaft 25-hp foundry crane speed reducer contains a helical gear with a pitch diameter of 8.08 in. Helical gears transmit components of force in the tangential, radial, and axial directions. The components of the gear force transmitted to the second shaft are shown in Fig. (8) at point A. The bearing reactions at C and D, assuming simple- supports, are also shown. A ball bearing is to be selected for location C to accept the thrust, and a cylindrical roller bearing is to be utilized at location D. The life goal of the speed reducer is 10 kh, with a reliability factor for the ensemble of all four bearings (both shafts) to equal 1 (90%% reliability) with light to moderate impact. (a) Select the roller bearing for location D. (6) Select the ball bearing (angular contact) for location C, assuming the inner ring rotates. Fig.(8)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

Q: A gear train is composed of four helical gears with the three shaft axes in a single plane, as shown…

Q: Calculate the angle of twist at point A. A for the following diagrammed problem. There is a 1600…

A: The diameter of shaft AB is .The diameter of shaft CD is .The diameter of gear B is .The diameter of…

Q: In the figure, shaft AB transmits power to shaft CD through a set of bevel gears contacting at point…

Q: Question 3 AC The circular stepped shaft ABD shown in Figure Q3 has its ends fixed against rotation.…

A: Step 1: Step 2: Step 3: Step 4: solution is given above

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

Q: (a) List down 2 assumptions needed in designing the shaft in Fig. 3. Design the minimum allowable…

A: DefinitionBending Moment:If an object undergoes a bend about its certain axis due to some tendency…

Q: 03/ The manually - operated hoist shown in figure (13) is based on an epicyclic gear train. The sun…

A: Given: The number of teeth on annulus, Za = 90 The tangential force on handle = 25 x load lifted

Q: 3. A steel shaft 60 in. long has applied to it a 10,000 in-lb torque by a pulley located at the…

Q: A steel cable is supporting a load of F = 9800 lb and is wrapped around a drum attached to gear A as…

Q: below. Determine: (1) the torque in shaft c-d to the nearest in-lb and (2) the angle of twist at…

A: To determine the torque in the shaft and the angle of twist at a pointgivenradius of gear b=radius…

Q: A motor provides 60 hp power to a wheel B. It rotates a solid shaft in AISI 1020 steel, 4 cm in…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Ex:
The second shaft on a parallel-shaft 25-hp foundry crane speed reducer
contains a helical gear with a pitch diameter of S.08 in. Helical gears
transmit components of force in the tangential, radial, and axial directions.
The components of the gear force transmitted to the second shaft are shown
in Fig. (8) at point A. The bearing reactions at C and D, assuming simple-
supports, are also shown. A ball bearing is to be selected for location C to
accept the thrust, and a cylindrical roller bearing is to be utilized at location
D. The life goal of the speed reducer is 10 kh, with a reliability factor for
the ensemble of all four bearings (both shafts) to equal 1 (90% reliability)
with light to moderate impact.
(a) Select the roller bearing for location D.
(b) Select the ball bearing (angular contact) for location C, assuming the
inner ring rotates.
*-
20
Fig (8)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 THE SOLUTION IS TOO LOND SO INSTEAD OF TYPING, I'M SHARING YOU THE SNAPSHOTS OF THE SOLUTION

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Homework help
Mechanics
please help solve
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
Question 1 An epicyclic gear train, as shown in Fig. 1, has a sun wheel S of 30 teeth and two planet wheels P-P of 50 teeth. The planet wheels mesh with the internal teeth of a fixed annulus A. The driving shaft carrying the sun-wheel S, transmits 4 kW at 300 r.p.m. The driven shaft is connected to an arm which carries the planet wheels. 1.1 Tabulate a table of motion for the given epicyclic gear train. 1.2 Determine the number of teeth in gear A, assume module is the same on all the gears. 1.3 Determine the speed of the arm or the driven shaft. 1.4 Determine the torque of the sun. 1.5 Determine the torque of the arm if the overall efficiency is 95 %. Arm S A a. 1 Figure 1: An epicyclic gear train
Problem 3
Problem : A train of spur gears with 20°full-depth involute teeth is shown in the Figure below. Gear 1 is the driving gear and transmits 50 kW power at 300 rpm to the gear train. The number of teeth on gears 1, 2, 3 and 4 are 30, 60, 25 and 50 respectively, while the module for all gears is 8 mm. Gears 2 and 3 are mounted on the same shaft. Gear 1 is rotating in the clockwise direction when seen from the left side of the page. The shaft is made of plain carbon steel 40C8 (Syt = 380 N/mm2) and the factor of safety is 2. Using maximum shear stress theory, estimate suitable diameter of shaft. 150 500 125 3 B1 B2
Parvinbhai
Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each seg- ment, and then plot the torsional moment diagram. Assume that the spacing between gears is constant, i.e., 10 in. T1 = T2 = 1000 lb-in. 500 lb-in. A B T3 = 800 Ib-in. C Ta = 500 lb-in. d = 1.0 in. D T; = 800 lb-in. E
A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long (0.5 m to the left and right of the gear) 50 mm diameter solid circular shaft, and power is taken from the two shaft ends. 25 kW is taken on the left end and an unknown amount of power is taken at the right end. the torque to the left side of the gear is? maximum shear stress to left of gear? If the maximum shear stress on the shaft to the right of the gear is 125 MPa, approximately how much power is being drawn off from the right side of the shaft? The shaft can be made from 6061-T6 aluminum. It has adequate strength to withstand the loading conditions in the scenario, including the loading on the right side of the shaft. true or false?
Problem 2: Consider the two gears mounted on the shaft, as shown. Distances are L1 = 100 mm, L2 = 250 mm, and L3 = 175 mm. Diameter of shaft AB is 15 mm, diameter of shaft BC is 20 mm, and diameter of shaft CD is 17.5 mm. Young's modulus for each portion is 200 GPa. Determine the displacement of point D with reference to point A. Also, determine the displacement of point A relative to C. b. Determine the axial strain at any point in shaft segments AB, BC and CD, respectively. If Poisson's ratio for the material of the shafts is v = 0.2, determine the lateral strain in each of the shaft segments. Based on your answers to part (a), do the gears move towards each other, or do they separate from each other? Note that in real gearboxes, movement of gears towards or away from each other is prevented by using thrust bearings. 10 kN 4 kN 5 kN 7 kN 4 kN NY 0I 17.
A solid constant-diameter circular shaft is subjected to the torques of TA = 560 lb·ft, TB = 1080 lb·ft, TC = 850 lb·ft, and TD = 330 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely.(a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6.(b) If the allowable shear stress in the shaft is 4200 psi, what is the minimum acceptable diameter for the shaft?