Consider the following figure:0.6"d0.5k₁ = 00.403=0kh = 0.20.30.0250.20.050.10.10.20-0.1↓051015202530 354045' (deg)For a retaining wall with a vertical back and horizontal backfill with a c'-' soil, the following are given:H = 10 ftY = 111 lb/ft³' = 25°kh = 0.2k₁ = 0c = 113 lb/ft²Determine the magnitude of active force Pae on the wall.(Enter your answer to two significant figures.)Pae=lb/ft

Answered: Consider the following figure: 0.6 "d…

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter15: Retaining Walls, Braced Cuts, And Sheet Pile Walls

Section: Chapter Questions

Problem 15.6P

See similar textbooks

Similar questions

Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The distance between the two column loads L3 = 13.5 ft. The proximity of the property line at the left edge requires that L2 = 3.0 ft. The net allowable soil pressure is 2500 lb/ft2. Determine the breadth and length of a rectangular combined footing.
Consider a continuous foundation of width B = 1.4 m on a sand deposit with c = 0, = 38, and = 17.5 kN/m3. The foundation is subjected to an eccentrically inclined load (see Figure 6.33). Given: load eccentricity e = 0.15 m, Df = 1 m, and load inclination = 18. Estimate the failure load Qu(ei) per unit length of the foundation a. for a partially compensated type of loading [Eq. (6.89)] b. for a reinforced type of loading [Eq. (6.90)]
A 2 m 3 m spread footing placed at a depth of 2 m carries a vertical load of 3000 kN and a moment of 300 kN m, as shown in Figure P6.14. Determine the factor of safety using Meyerhofs effective area method. Figure P6.14
Refer to Figure 15.27a. For the braced cut, H = 6 m, Hs = 2 m, s = 16.2 kN/m3, angle of friction of sand, s=34, Hc = 4 m, c = 17.5 kN/m3, and the unconfined compression strength of the clay layer, qu = 68 kN/m2. a. Estimate the average cohesion, cav, and the average unit weight, av, for development of the earth pressure envelope. b. Plot the earth pressure envelope. FIG. 15.27 Layered soils in braced cuts
The water table at a site is at 5 m below the ground level, and it is required to excavate to this level. The soil profile consists of a thick bed of sand where the unit weight is m = 17.0 kN/m3 above the water table and sat = 20.0 kN/m3 below the water table. The friction angle of the sand is 37. The wall of the excavation will be supported by cantilever sheet piles. How deep would you drive the sheet piles? Use the simplified analysis (Figure 15.37) with a factor of safety of 1.5 on the passive resistance. Determine the maximum bending moment in the sheet pile and the required section modulus for the sheet pile section (given an allowable stress of 190 MN/m2).
A braced cut is carried out to 10 m depth at a site where the soil consists of 4 m of sand ( = 17.0 kN/m3, = 33) at the top underlain by 6 m of clay ( = 18.5 kN/m3, c = 35 kN/m2). a. What would be the average value of cohesion and the unit weight for the equivalent homogeneous soil profile? b. Show the lateral earth pressure envelope you would use in determining the strut loads.
A column foundation (Figure P6.9) is 3 m × 2 m in plan. Given: Df = 1.5 m, ф′ = 25°, c′ = 70 kN/m2. Using Eq. (6.28) and FS = 3, determine the net allowable load [see Eq. (6.24)] the foundation could carry. Figure P6.9
Redo Problem 14.1 with the following: L1 = 3m, L2 = 6 m, γ = 17.3 kN/m3, γsat = 19.4 kN/m3, and ϕ′ = 30°. 14.1 Figure P14.1 shows a cantilever sheet-pile wall penetrating a granular soil. Here, L1 = 4 m, L2 = 8 m, γ = 16.1 kN/m3, γsat = 18.2 kN/m3, and ϕ′ = 32°. What is the theoretical depth of embedment, D? For a 30% increase in D, what should be the total length of the sheet piles? Determine the theoretical maximum moment of the sheet pile.
The cross section of a braced cut supporting a sheet pile installation in a clay soil is shown in Figure 14.22. Given: H = 12 m, clay = 17.9 kN/m3, = 0, c = 75 kN/m2, and the center-to-center spacing of struts in plan view, s = 3 m. a. Using Pecks empirical pressure diagrams, draw the earth-pressure envelope. b. Determine the strut loads at levels A, B, and C.

Recommended textbooks for you

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781305081550

Author:

Braja M. Das

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781305081550

Author:

Braja M. Das

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Principles of Geotechnical Engineering (MindTap C…

Civil Engineering

ISBN:

9781305970939

Author:

Braja M. Das, Khaled Sobhan

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS